06-03-2015 02:15 AM - edited 03-08-2019 12:19 AM
hello community
i try to set up QoS a new 6807 switch with sup2T and a WS-X6824-SFP card.
according the medianet QoS desgn guide and config guide for version 15.1SY the sup2t supports MQC (3CPL) policy based for queueing.
since the WS-X6824-SFP card has 2P3Q8T, i tried the following config:
policy-map type lan-queuing p_map_1p3q8t
class type lan-queuing c_map_cos_5
priority
class type lan-queuing c_map_cos_6_7
bandwidth remaining percent 40
queue-buffers ratio 15
random-detect cos-based aggregate
random-detect cos values 6 7 percent 70 100
class type lan-queuing c_map_cos_2_3_4
bandwidth remaining percent 30
queue-buffers ratio 20
random-detect cos-based
random-detect cos 2 percent 40 70
class class-default
bandwidth remaining percent 25
queue-buffers ratio 20
random-detect cos-based
random-detect cos 0 percent 40 70
random-detect cos 1 percent 70 100
this part works. class maps type lan-queuing are defined as well.
but when i am applying the "service-policy type lan-queuing output p_map_1p3q8t" to the Gigabit ports, it say:
Propagating [attach] lan queueing policy "p_map_1p3q8t" to Gi1/1/2 Gi1/1/3 Gi1/1/4 Gi1/1/5 Gi1/1/6 Gi1/1/7 Gi1/1/8 Gi1/1/9 Gi1/1/10 Gi1/1/11 Gi1/1/12
BUT the service policy is goes not active on the ports. and the "sh policy-map type lan-queuing interface" shows nothing.
i am wrong with my config / thinking? can sombody point me to the right direction.
TIA
juergen
Solved! Go to Solution.
06-09-2015 08:57 AM
Hi Jürgen
Try to remove "bandwidth remaining percent 25" in the class-default and attach the service policy to all interface which belong to the same port asic. WS-X6824-SFP have two port asic. As I know ports 1-12 share port asic 1 and port 13-24 are on port asic two.
Therefore attach it like that:
interface range Gi1/1/1-12
service-policy type lan-queuing output p_map_1p3q8t
If you also need the queuing polic on lets say Gi1/1/15 then you need it also to attach to:
interface range Gi1/1/13-24
service-policy type lan-queuing output p_map_1p3q8t
Cheers
Luke
06-09-2015 08:57 AM
Hi Jürgen
Try to remove "bandwidth remaining percent 25" in the class-default and attach the service policy to all interface which belong to the same port asic. WS-X6824-SFP have two port asic. As I know ports 1-12 share port asic 1 and port 13-24 are on port asic two.
Therefore attach it like that:
interface range Gi1/1/1-12
service-policy type lan-queuing output p_map_1p3q8t
If you also need the queuing polic on lets say Gi1/1/15 then you need it also to attach to:
interface range Gi1/1/13-24
service-policy type lan-queuing output p_map_1p3q8t
Cheers
Luke
06-10-2015 12:03 AM
thank you luke!
already found that wrong point. :)
and it hited a bug as well. so the telnet session did not gave me a feedback.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide