Sure thing. This is just a config that I pieced together. No idea what works or doesn't since it needs to be shipped to the remote location. But this is for starters at least....I know if have the Bell.ca modems in the attached pic, i'm thinking they will actually be removed. I'd rather come right from the wall jacks to the router on the outside. Gig 0/0 will patch over to X3 on the Sonicwall, and X0 will patch over to the switch.
I still need to lock it down, but right now I'm more interested in just getting an internet connection since I'll be configuring the final version remotely with no IT support on the remote end.
DPAI#sh run
Building configuration...
Current configuration : 2786 bytes
!
! Last configuration change at 17:37:54 UTC Tue Feb 4 2014
version 15.2
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime
service password-encryption
!
hostname DPAI
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
!
no ipv6 cef
no ip source-route
!
!
!
!
!
ip cef
multilink bundle-name authenticated
!
!
!
license udi pid CISCO1921/K9 sn FGL1532220J
!
!
!
!
controller VDSL 0/0/0
operating mode vdsl2
sra
!
controller VDSL 0/1/0
operating mode vdsl2
sra
!
!
!
!
!
interface Embedded-Service-Engine0/0
no ip address
shutdown
!
interface GigabitEthernet0/0
ip address 192.168.1.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface ATM0/0/0
no ip address
ip nat outside
ip virtual-reassembly in
no atm ilmi-keepalive
pvc 0/35
pppoe-client dial-pool-number 2
pppoe-client dial-pool-number 1
!
!
interface Ethernet0/0/0
no ip address
pppoe enable group global
pppoe-client dial-pool-number 2
pppoe-client dial-pool-number 1
!
interface ATM0/1/0
no ip address
ip nat outside
ip virtual-reassembly in
no atm ilmi-keepalive
pvc 8/35
pppoe-client dial-pool-number 2
pppoe-client dial-pool-number 1
!
!
interface Ethernet0/1/0
no ip address
pppoe enable group global
pppoe-client dial-pool-number 2
pppoe-client dial-pool-number 1
!
interface Dialer1
mtu 1460
ip address 70.55.236.225 255.255.255.0
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication pap chap callout
ppp chap hostname txxxx@bellnet.ca
ppp chap password 7 044F5B515E725E4B0E
ppp pap sent-username txxxx@bellnet.ca password 7 044F5B515E725E4B0E59
!
interface Dialer2
mtu 1460
ip address 76.70.1.69 255.255.255.0
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 2
dialer-group 2
ppp authentication pap chap callout
ppp chap hostname txxxx@bellnet.ca
ppp chap password 7 03100B5D5F5C334949
ppp pap sent-username txxxx@bellnet.ca password 7 09581E5F405605170C4C
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
ip nat source static tcp 192.168.1.253 4433 interface GigabitEthernet0/0 4433
ip nat inside source list 99 interface Dialer1 overload
ip route 0.0.0.0 0.0.0.0 Dialer1
!
access-list 99 permit 192.168.1.0 0.0.0.255
dialer-list 1 protocol ip permit
dialer-list 2 protocol ip permit
!
!
!
control-plane
!
!
!
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
login
transport input all
!
scheduler allocate 20000 1000
!
end
And yes, the dialer info, ATM, pretty much anything with the VA-DSL-A card I was pretty much winging. If you see anything that's not needed/wrong/incomplete or just plain nonsensical, by all means let me know. It's connecting to 2 VDSL lines in Ontario and Bell Canada does not support this config.
Thanks again.
