cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
560
Views
1
Helpful
9
Replies

Catalyst 3650 OS image not auto booting after restart

Jack96
Level 1
Level 1
9 Replies 9

Leo Laohoo
Hall of Fame
Hall of Fame

Did someone conduct password recovery on the switch?

Not recovery password and I saved the boot image but after restart boot is entering rommon

 

If the switch is still in ROMMON, post the complete output to the command "set". 

If the switch has successfully boot into OS, post the complete output to the command "sh romvar".

this is romvar result

CS#show romvar
ROMMON variables:
0x2102=""
ASIC_PCI_RESET="1"
BOOT="flash:/packages.conf"
BOOT_LOADER_UPGRADE_DISABLE="1"
BYPASS_STARTUP_CONFIG="= 0"
CFG_MODEL_NUM="WS-C3650-24TS-L"
CLEI_CODE_NUMBER="IPMV810BRE"
CSR_PCIERST_DISCONNECTED="yes"
DEFAULT_GATEWAY="192.168.100.1"
DEFAULT_ROUTER="192.168.10.1"
D_STACK_DOMAIN_NUM="1"
ECI_CODE_NUMBER="470063"
IP_ADDR="192.168.10.10/255.255.255.0"
IP_ADDRESS="192.168.100.12"
IP_SUBNET_MASK="255.255.255.0"
MANUAL_BOOT="0"
MODEL_NUM="WS-C3650-24TS"
MODEL_REVISION_NUM="R0"
MOTHERBOARD_REVISION_NUM="A0"
MOTHERBOARD_SERIAL_NUM="FDO22322VX5"
RECOVERY_BUNDLE="sda9:cat3k_caa-recovery.bin"
SCH_IGNORE_STARTUP_CFG="1"
SWITCH_IGNORE_STARTUP_CFG="= 0"
SWITCH_PRIORITY="2""
TAN_NUM="800-41246-03"
TAN_REVISION_NUMBER="D0"
TEMPLATE="advanced"
TERMLINES="0"
TFTP_FILE="cat3k_caa-universalk9.16.12.12.SPA.bin"
TFTP_SERVER="192.168.100.10"
VERSION_ID="V04"
boBOOT="= flash:packages.conf"
boot="= flash:packages.conf"

Post the complete output to the command "sh boot". 

Console into the switch and reboot.  Post the entire boot-up process.

CS#show post
Stored system POST messages:

Switch 1
---------

POST: MBIST Tests : Begin
POST: MBIST Tests : End, Status Passed

POST: CRYPTO Tests : Begin
POST: CRYPTO Tests : End, Status Passed

POST: PHY Loopback: loopback Test : Begin
POST: PHY Loopback: loopback Test : End, Status Passed

POST: Thermal, Temperature Tests : Begin
POST: Thermal, Temperature Tests : End, Status Passed

POST: Thermal, Fan Tests : Begin
POST: Thermal, Fan Tests : End, Status Passed

POST: SIF Tests : Begin
POST: SIF Tests : End, Status Passed

Post the complete output to the command "sh boot". 

Console into the switch and reboot.  Post the entire boot-up process.

just want to help there 
he use two 
TFTP_FILE="cat3k_caa-universalk9.16.12.12.SPA.bin"
TFTP_SERVER="192.168.100.10"

BOOT="flash:/packages.conf" <<- this config files 

are this correct ??

MHM

Jens Albrecht
Spotlight
Spotlight

Looks like someone has screwed up the ROMMON variables:

JensAlbrecht_0-1756199852077.png

You need to clean up this mess and then check again.