cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1368
Views
0
Helpful
1
Replies

Cisco 7606 and WS-X6748-GE-TX issue

g.pregnolato
Level 1
Level 1

I have one Cisco 7606 and i need to install a WS-X6748-GE-TX with WS-F6700-DFC3CXL.

When I install the WS-X6748-GE-TX the module is powered off with the following warning:

00:01:45: %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 1, power not allowed: Unsupported baseboard/earl combination.

The IOS release is: 12.2(18)SXF15

The "show module" command shows:

------------------ show module ------------------

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  1   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     JAF1219CDKQ

  3   48  48 port 10/100 mb RJ45                 WS-X6348-RJ-45     SAL08207TE3

  4   16  SFM-capable 16 port 1000mb GBIC        WS-X6516-GBIC      SAL08496YC8

  5    2  Supervisor Engine 720 (Active)         WS-SUP720-3BXL     SAL1126SFZH

  6    2  Supervisor Engine 720 (Hot)            WS-SUP720-3B       SAL1230Y9X0

Mod MAC addresses                       Hw    Fw           Sw           Status

--- ---------------------------------- ------ ------------ ------------ -------

  1  001f.cae6.e9ac to 001f.cae6.e9db   2.8   Unknown      Unknown      PwrDown

  3  0011.210c.9fc8 to 0011.210c.9ff7   9.0   5.4(2)       8.5(0.46)RFW Ok

  4  0012.d92b.89a8 to 0012.d92b.89b7   5.7   7.2(1)       8.5(0.46)RFW Ok

  5  0016.9df7.0564 to 0016.9df7.0567   5.6   8.5(2)       12.2(18)SXF1 Ok

  6  001c.58d0.c3f0 to 001c.58d0.c3f3   5.8   8.5(4)       12.2(18)SXF1 Ok

Mod  Sub-Module                  Model              Serial       Hw     Status

---- --------------------------- ------------------ ----------- ------- -------

  1  Distributed Forwarding Card WS-F6700-DFC3CXL   SAL1213KAUJ  1.1    PwrDown

  5  Policy Feature Card 3       WS-F6K-PFC3BXL     SAL1126SV4P  1.8    Ok

  5  MSFC3 Daughterboard         WS-SUP720          SAL1126SL7G  3.1    Ok

  6  Policy Feature Card 3       WS-F6K-PFC3BXL     JAF1216AHHT  1.9    Ok

  6  MSFC3 Daughterboard         WS-SUP720          SAL1230Y30R  3.5    Ok

Mod  Online Diag Status

---- -------------------

  1  Not Applicable

  3  Pass

  4  Pass

  5  Pass

  6  Pass

Anybody knows why the combination of baseboard/earl it´s unsupported.

Thanks,

Giuseppe

1 Reply 1

Reza Sharifi
Hall of Fame
Hall of Fame

Hi Giuseppe,

This module is supported on the 6500 series and not 7600.

There are spesific card that are supported in both, but this is not one og them:

odules

• Cisco Catalyst 6500 Series 10 Gigabit Ethernet Interface Modules Data Sheet

• Cisco Catalyst 6500 Series Gigabit Ethernet Interface Modules Data Sheet

• Cisco Catalyst 6500 Series 10/100 and 10/100/1000 Ethernet Interface Modules Data Sheet

Layer 4-7 Modules

• Cisco Catalyst 6500 Series Communication Media Module

• Cisco Catalyst 6000 Family Voice T1 and Services Module

• Cisco Catalyst 6500 Series Cisco Content Switching Module

• Cisco Content Services Gateway

• Cisco Catalyst 6500 Series Firewall Services Module

• Cisco Catalyst 6500 Series IDS Module (IDSM-2)

• IPSec VPN Services Module for the Cisco Catalyst 6500 Switch and Cisco 7600 Router

• Cisco Multiprocessor WAN Application Mode

• Cisco Catalyst 6500 Series NAM (NAM-1/NAM-2)

• Cisco Persistent Storage Device

• SSL Services Module for the Cisco Catalyst 6500 Series and Cisco 7600 Series

• Cisco Catalyst 6500 Series Wireless LAN Services Module

FlexWAN, Optical Services Modules, and ATM

• Cisco 7600 Series and Cisco Catalyst 6500 Series Optical Services Modules

• Cisco 7600 Series and Cisco Catalyst 6500 Series Enhanced FlexWAN Module

• FlexWAN Module for the Cisco Catalyst 6500 Series and Cisco 7600 Series

• New High-Speed ATM LANE/MPOA Modules

more info:

http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps708/product_data_sheet0900aecd8017376e.html

HTH

Review Cisco Networking for a $25 gift card