Hello
I have a problem with Cisco 837. First of all, I didn't set it up. It was setup ready by the fellows from the phonecompany. Everything is running fine, internet and other connections work how they are supposed to but I can't access any settings through CRWS. I just get the "page not found" when I try to access the default address 10.10.10.1 . I have also tried the address 192.168.1.1 . I went through the password recovery procedure to gain access to the CLI settings, but I have no idea of what to do to get the CRWS to work. I know CRWS is installed on the router and I know SDM is not. I have tried everything described in the quick start manual. I also tried giving the Ethernet0 an IP address, that didn't do anything.
The router is connected to a switch to wich all the computers are connected. Computers have the an IP of 192.168.1.x in 255.255.255.0 subnetmask. And router has static IP from the ISP. There is also some sort of decrypted bridge connection to another network.
I'm not really sure of what info you would need but here is the running-config
Current configuration : 2322 bytes
!
version 12.2
no service pad
service timestamps debug datetime localtime
service timestamps log datetime localtime
service password-encryption
!
hostname Laakarias_Niemela
!
logging buffered 10000 debugging
enable secret xxxx
enable password xxxx
!
ip subnet-zero
no ip source-route
!
ip cef
ip inspect name muuri tcp
ip inspect name muuri udp
ip inspect name muuri ftp
ip inspect name muuri h323
ip audit notify log
ip audit po max-events 100
vpdn enable
!
vpdn-group pppoe
request-dialin
protocol pppoe
!
!
!
bridge irb
!
!
interface Ethernet0
ip address 192.168.1.50 255.255.255.0
bridge-group 1
hold-queue 100 out
!
interface ATM0
no ip address
no atm ilmi-keepalive
dsl operating-mode ansi-dmt
dsl power-cutback 0
hold-queue 224 in
!
interface ATM0.1 point-to-point
ip access-group 100 in
no ip proxy-arp
ip inspect muuri out
pvc 0/50
pppoe-client dial-pool-number 1
!
!
interface ATM0.2 point-to-point
description Silta Sjoki
pvc 0/40
encapsulation aal5snap
!
bridge-group 1
!
interface Dialer0
ip address negotiated
ip mtu 1492
ip nat outside
encapsulation ppp
dialer pool 1
dialer-group 1
ppp pap sent-username xxxx password xxxx
!
interface BVI1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip tcp adjust-mss 1452
!
ip nat inside source list 101 interface Dialer0 overload
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
!
!
access-list 20 permit 62.148.194.0 0.0.0.255
access-list 20 permit 192.168.1.0 0.0.0.255
access-list 20 deny any log
access-list 100 deny ip 192.168.1.0 0.0.0.255 any log
access-list 100 deny ip host 255.255.255.255 any log
access-list 100 permit icmp any any echo-reply
access-list 100 permit icmp any any time-exceeded
access-list 100 permit icmp any any packet-too-big
access-list 100 permit icmp any any traceroute
access-list 100 permit icmp any any unreachable
access-list 100 deny ip any any log
access-list 101 permit ip 192.168.1.0 0.0.0.255 any
dialer-list 1 protocol ip permit
bridge 1 protocol ieee
bridge 1 route ip
!
line con 0
password xxxx
no modem enable
stopbits 1
line aux 0
stopbits 1
line vty 0 4
access-class 20 in
exec-timeout 120 0
password xxxx
login
!
scheduler max-task-time 5000
end
