out put of my sh boot, sho romvar, dir, sh run all | in service, sh ver, and sh log. I've set it to boot from packages.conf (after a regular install activate commit of the bin) and the bin file both. CONFIG_FILE= is obviously blank and I would assume needs to point to the startup-config file?
Switch#sh boot
---------------------------
Switch 1
---------------------------
Current Boot Variables:
BOOT variable does not exist
Boot Variables on next reload:
BOOT variable = flash:cat9k_iosxe.17.12.04.SPA.bin;
Manual Boot = no
Enable Break = no
Boot Mode = DEVICE
iPXE Timeout = 0
Switch#sh romvar
----------------------------------
ROMMON variables for Active Switch
----------------------------------
ABNORMAL_RESET_COUNT=0
AUTO_SWITCH_CONSOLE_DISABLE=0
BAUD=9600
BOARDID=24658
BOOT=flash:cat9k_iosxe.17.12.04.SPA.bin;
BOOTLDR=
BSI=0
CONFIG_FILE=
CONSOLE_MIRRORING_DISABLE=0
CSDL_MODE_DISABLE=1
DC_COPY=yes
IMAGE_UPGRADE=no
LICENSE_BOOT_LEVEL=network-advantage+dna-advantage,all:C9300_24P;
MAC_ADDR=00:87:64:5C:35:80
MANUAL_BOOT=no
MODEL_NUM=C9300-24UX
MODEL_REVISION_NUM=A0
MOTHERBOARD_ASSEMBLY_NUM=73-18276-03
MOTHERBOARD_REVISION_NUM=A0
MOTHERBOARD_SERIAL_NUM=FOC23056716
RANDOM_NUM=301285614
RET_2_RCALTS=
RET_2_RTS=
ROMMON_AUTOBOOT_ATTEMPT=3
SWITCH_IGNORE_STARTUP_CFG=1
SWITCH_NUMBER=1
SYSTEM_SERIAL_NUM=FCW2308D060
TEMPLATE=access
USB_DISABLE=0
VERSION_ID=V02
Switch#dir
Directory of flash:/
606244 -rw- 0 Oct 27 2024 13:42:18 +00:00 dope_hist
606238 -rw- 17013 Oct 27 2024 13:42:18 +00:00 rdope_out.txt
606239 -rw- 89 Oct 27 2024 13:42:17 +00:00 rdope.log
606211 -rw- 2097152 Oct 27 2024 13:42:05 +00:00 nvram_config_bkup
606210 -rw- 2097152 Oct 27 2024 13:42:05 +00:00 nvram_config
606243 -rw- 3736 Oct 27 2024 13:41:59 +00:00 vlan.dat
696321 drwx 4096 Oct 27 2024 13:41:52 +00:00 .prst_sync
8193 drwx 4096 Oct 27 2024 13:41:41 +00:00 .installer
606237 -rw- 15 Oct 27 2024 13:41:24 +00:00 rmon_var_template
606231 -rwx 2049 Oct 27 2024 13:41:13 +00:00 svl_ipc.tcl
606230 -rw- 138115 Oct 27 2024 13:41:13 +00:00 memleak.tcl
606229 -rw- 437 Oct 27 2024 13:40:56 +00:00 boothelper.log
81954 drwx 4096 Oct 27 2024 13:40:54 +00:00 dc_profile_dir
606226 -rw- 210 Oct 27 2024 13:40:45 +00:00 mcelog.txt
606225 -rw- 222 Oct 27 2024 13:40:45 +00:00 bootloader_evt_handle.log
606252 -rw- 1306917133 Oct 27 2024 04:06:59 +00:00 cat9k_iosxe.17.12.04.SPA.bin
606251 -rw- 27 Oct 27 2024 03:26:22 +00:00 mcu_debug.txt
606249 -rw- 1175 Oct 27 2024 03:26:22 +00:00 .packages.verify.log
606250 -rw- 1660 Oct 27 2024 03:26:21 +00:00 fpgahelper.log
606248 -rw- 1074 Oct 27 2024 03:26:21 +00:00 .mb_fpgapackages.log
606247 -rw- 526 Oct 27 2024 03:24:36 +00:00 preboothelper.log
606246 -rw- 412 Oct 27 2024 03:24:36 +00:00 .bootpackages.verify.log
606245 -rw- 384 Oct 27 2024 03:24:35 +00:00 .iox_alt_hdd_cleanup.log
8195 drwx 4096 Oct 27 2024 03:09:57 +00:00 .dbpersist
606242 -rw- 4860 Oct 27 2024 03:08:38 +00:00 backup2.cfg
606241 -rw- 9176 Oct 27 2024 03:08:25 +00:00 backup.cfg
16386 drwx 4096 Oct 27 2024 03:07:28 +00:00 core
139271 drwx 4096 Oct 27 2024 03:07:26 +00:00 onep
122881 drwx 4096 Oct 27 2024 03:00:28 +00:00 .rommon_sync
606236 -rw- 1261 Oct 27 2024 03:00:25 +00:00 Baltimore.ca
606235 -rw- 1606 Oct 27 2024 03:00:25 +00:00 StarfieldServicesRootCA.ca
606234 -rw- 1924 Oct 27 2024 03:00:25 +00:00 ISRGRootX1CrossSignDST.ca
606233 -rw- 1338 Oct 27 2024 03:00:25 +00:00 DigiCertGlobalRootCA.ca
114689 drwx 4096 Oct 27 2024 03:00:23 +00:00 Tbot
98305 drwx 4096 Oct 27 2024 03:00:15 +00:00 fp_cc_crash
90113 drwx 4096 Oct 27 2024 03:00:15 +00:00 sys_report
81957 drwx 4096 Oct 27 2024 03:00:14 +00:00 EDScisco
81921 drwx 4096 Oct 27 2024 03:00:13 +00:00 tech_support
65537 drwx 4096 Oct 27 2024 03:00:06 +00:00 .rollback_timer
12 drwx 4096 Oct 27 2024 02:59:17 +00:00 pcap
606224 -rwx 0 Oct 27 2024 02:59:17 +00:00 mode_event_log
688129 drwx 4096 Oct 27 2024 02:59:17 +00:00 SHARED-IOX
606223 -rw- 61891845 Oct 27 2024 02:57:23 +00:00 cat9k-rpboot.17.12.04.SPA.pkg
606222 -rw- 6562 Oct 27 2024 02:57:23 +00:00 packages.conf
606221 -rw- 9216 Oct 27 2024 02:57:23 +00:00 cat9k-wlc.17.12.04.SPA.pkg
606220 -rw- 17884160 Oct 27 2024 02:57:23 +00:00 cat9k-webui.17.12.04.SPA.pkg
606219 -rw- 41288708 Oct 27 2024 02:57:22 +00:00 cat9k-srdriver.17.12.04.SPA.pkg
606218 -rw- 56431616 Oct 27 2024 02:57:22 +00:00 cat9k-sipspa.17.12.04.SPA.pkg
606217 -rw- 48747524 Oct 27 2024 02:57:22 +00:00 cat9k-sipbase.17.12.04.SPA.pkg
606216 -rw- 768689152 Oct 27 2024 02:57:21 +00:00 cat9k-rpbase.17.12.04.SPA.pkg
606215 -rw- 111498240 Oct 27 2024 02:57:20 +00:00 cat9k-lni.17.12.04.SPA.pkg
606214 -rw- 2155524 Oct 27 2024 02:57:20 +00:00 cat9k-guestshell.17.12.04.SPA.pkg
606213 -rw- 169464836 Oct 27 2024 02:57:20 +00:00 cat9k-espbase.17.12.04.SPA.pkg
606212 -rw- 29471752 Oct 27 2024 02:57:20 +00:00 cat9k-cc_srdriver.17.12.04.SPA.pkg
11353194496 bytes total (8118927360 bytes free)
Switch#
Switch#
Switch#sh run all | in service
no service log backtrace
no service config
no service exec-callback
no service nagle
service slave-log
no service slave-coredump
no service pad to-xot
no service pad from-xot
no service pad cmns
no service pad
no service telnet-zeroidle
no service tcp-keepalives-in
no service tcp-keepalives-out
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
no service private-config-encryption
no service exec-wait
no service linenumber
no service internal
no service log-hidden
no service scripting
no service compress-config
service prompt config
no service old-slip-prompts
no service hide-telnet-addresses
no service pt-vty-logging
no service disable-ip-fast-frag
no service sequence-numbers
service counters max age 0
service dhcp
no service call-home
no service performance
service-routing capabilities-manager
service-policy input system-cpp-policy
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
cloud-services endpoint api/tethering/v1/enrollment/enroll/byname
cloud-services url https://dnaservices.cisco.com
Switch#
Switch#
Switch#sh log
Syslog logging: enabled (0 messages dropped, 2 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)
No Active Message Discriminator.
No Inactive Message Discriminator.
Console logging: level debugging, 125 messages logged, xml disabled,
filtering disabled
Monitor logging: level debugging, 0 messages logged, xml disabled,
filtering disabled
Buffer logging: level debugging, 125 messages logged, xml disabled,
filtering disabled
Exception Logging: size (4096 bytes)
Count and timestamp logging messages: disabled
File logging: disabled
Persistent logging: disabled
No active filter modules.
Trap logging: level informational, 124 message lines logged
Logging Source-Interface: VRF Name:
TLS Profiles:
Log Buffer (102400 bytes):
*Oct 27 13:41:43.802: %CRYPTO-5-SELF_TEST_START: Crypto algorithms release (Rel5a), Entropy release (3.4.1)
begin self-test
*Oct 27 13:41:44.633: %CRYPTO-5-SELF_TEST_END: Crypto algorithms self-test completed successfully
All tests passed.
*Oct 27 13:41:49.116: %SMART_LIC-6-AGENT_ENABLED: Smart Agent for Licensing is enabled
*Oct 27 13:41:49.178: %SMART_LIC-6-EXPORT_CONTROLLED: Usage of export controlled features is not allowed
*Oct 27 13:41:52.886: pagp init: platform supports EC/LACP xFSU
*Oct 27 13:41:54.457: ISIS-GRACEFUL-RELOAD: Init State GR_NONE
*Oct 27 13:41:54.502: LACP-GR: infra cb, GR_NONE
*Oct 27 13:41:54.638: %TLSCLIENT-5-TLSCLIENT_IOS: TLS Client is IOS based
*Oct 27 13:41:55.085: %CRYPTO-4-AUDITWARN: Encryption audit check could not be performed
*Oct 27 13:41:55.085: %CRYPTO_ENGINE-4-CSDL_COMPLIANCE_DISABLED: Cisco PSB security compliance has been disabled by platform
*Oct 27 13:41:55.229: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
*Oct 27 13:41:55.873: %LINK-5-UPDOWN: Interface Lsmpi18/3, changed state to up
*Oct 27 13:41:55.883: %LINK-5-UPDOWN: Interface EOBC18/1, changed state to up
*Oct 27 13:41:55.883: %LINEPROTO-5-UPDOWN: Line protocol on Interface LI-Null0, changed state to up
*Oct 27 13:41:55.884: %LINEPROTO-5-UPDOWN: Line protocol on Interface LIIN18/2, changed state to up
*Oct 27 13:41:55.884: %LINK-5-UPDOWN: Interface LIIN18/2, changed state to up
*Oct 27 13:41:55.884: %LINK-5-UPDOWN: Interface GigabitEthernet0/0, changed state to down
*Oct 27 13:41:55.884: %LINK-5-CHANGED: Interface Bluetooth0/4, changed state to administratively down
*Oct 27 13:41:56.017: %PNP-6-PNP_DISCOVERY_STARTED: PnP Discovery started
*Oct 27 13:41:56.056: %HMANRP-6-HMAN_IOS_CHANNEL_INFO: HMAN-IOS channel event for switch 1: EMP_RELAY: Channel UP!
*Oct 27 13:41:56.060: %HMANRP-6-EMP_NO_ELECTION_INFO: Could not elect active EMP switch, setting emp active switch to 0: EMP_RELAY: Could not elect switch with mgmt port UP
*Oct 27 13:41:36.439: %STACKMGR-6-STACK_LINK_CHANGE: Switch 1 R0/0: stack_mgr: Stack port 1 on Switch 1 is cable-not-connected
*Oct 27 13:41:36.439: %STACKMGR-6-STACK_LINK_CHANGE: Switch 1 R0/0: stack_mgr: Stack port 2 on Switch 1 is down
*Oct 27 13:41:36.440: %STACKMGR-6-STACK_LINK_CHANGE: Switch 1 R0/0: stack_mgr: Stack port 2 on Switch 1 is cable-not-connected
*Oct 27 13:41:36.440: %STACKMGR-4-SWITCH_ADDED: Switch 1 R0/0: stack_mgr: Switch 1 has been added to the stack.
*Oct 27 13:41:38.280: %STACKMGR-4-SWITCH_ADDED: Switch 1 R0/0: stack_mgr: Switch 1 has been added to the stack.
*Oct 27 13:41:40.293: %STACKMGR-4-SWITCH_ADDED: Switch 1 R0/0: stack_mgr: Switch 1 has been added to the stack.
*Oct 27 13:41:40.294: %STACKMGR-6-ACTIVE_ELECTED: Switch 1 R0/0: stack_mgr: Switch 1 has been elected ACTIVE.
*Oct 27 13:41:56.095: %NGWC_USB_CONSOLE-6-USB_INSERT: Switch 1: USB cable inserted. Console media-type USB is in effect
*Oct 27 13:41:56.095: %NGWC_USB_CONSOLE-6-USB_REMOVE: Switch 1: USB cable removed. Console media-type RJ45 is in effect
*Oct 27 13:41:56.095: %NGWC_USB_CONSOLE-6-USB_INSERT: Switch 1: USB cable inserted. Console media-type USB is in effect
*Oct 27 13:41:56.431: %HMANRP-6-EMP_NO_ELECTION_INFO: Could not elect active EMP switch, setting emp active switch to 0: EMP_RELAY: Could not elect switch with mgmt port UP
*Oct 27 13:41:56.469: ILP:: switch 1 POE mode : IEEE AT
*Oct 27 13:41:56.469: ILP:: POE POST detail for switch 1: PASS
*Oct 27 13:41:56.469: ILP:: Able to get POE POST from switch 1 MCU
*Oct 27 13:41:56.882: %LINEPROTO-5-UPDOWN: Line protocol on Interface Lsmpi18/3, changed state to up
*Oct 27 13:41:56.882: %LINEPROTO-5-UPDOWN: Line protocol on Interface EOBC18/1, changed state to up
*Oct 27 13:41:57.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to down
*Oct 27 13:41:57.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface Bluetooth0/4, changed state to down
*Oct 27 13:41:57.207: %SYS-5-CONFIG_P: Configured programmatically by process MGMT VRF Process from console as vty0
*Oct 27 13:41:57.547: %IOSXE_MGMTVRF-6-CREATE_SUCCESS_INFO: Management vrf Mgmt-vrf created with ID 1, ipv4 table-id 0x1, ipv6 table-id 0x1E000001
*Oct 27 13:41:57.554: %SYS-5-CONFIG_P: Configured programmatically by process MGMT VRF Process from console as vty0
*Oct 27 13:41:57.563: %IOSXE_MGMTVRF-6-CREATE_SUCCESS_INFO: Management vrf Mgmt-vrf created with ID 1, ipv4 table-id 0x1, ipv6 table-id 0x1E000001
*Oct 27 13:41:57.563: %SYS-5-CONFIG_P: Configured programmatically by process MGMT VRF Process from console as vty0
*Oct 27 13:41:57.849: %ONEP_BASE-6-SS_ENABLED: ONEP: Service set Base was enabled by Default
*Oct 27 13:41:58.207: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
*Oct 27 13:41:58.849: %SYS-6-STARTUP_CONFIG_IGNORED: System startup configuration is ignored based on the configuration register setting.
*Oct 27 13:41:59.013: %SYS-5-CONFIG_P: Configured programmatically by process CPP MQC QoS Policy manager from console as vty1
*Oct 27 13:41:59.016: %PLATFORM_FEP-6-FRU_PS_OIR: Switch 1: FRU power supply A inserted
*Oct 27 13:41:59.025: %CRYPTO-5-SELF_TEST_START: Crypto algorithms release (Rel5a), Entropy release (3.4.1)
begin self-test
*Oct 27 13:41:59.043: %CRYPTO-5-SELF_TEST_END: Crypto algorithms self-test completed successfully
All tests passed.
*Oct 27 13:42:00.327: %SYS-5-RESTART: System restarted --
Cisco IOS Software [Dublin], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 17.12.4, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2024 by Cisco Systems, Inc.
Compiled Tue 23-Jul-24 09:40 by mcpre
*Oct 27 13:42:01.672: %LINK-5-UPDOWN: Interface GigabitEthernet1/1/1, changed state to down
*Oct 27 13:42:01.673: %LINK-5-UPDOWN: Interface GigabitEthernet1/1/2, changed state to down
*Oct 27 13:42:01.673: %LINK-5-UPDOWN: Interface GigabitEthernet1/1/3, changed state to down
*Oct 27 13:42:01.674: %LINK-5-UPDOWN: Interface GigabitEthernet1/1/4, changed state to down
*Oct 27 13:42:01.674: %LINK-5-UPDOWN: Interface TenGigabitEthernet1/1/1, changed state to down
*Oct 27 13:42:01.676: %LINK-5-UPDOWN: Interface TenGigabitEthernet1/1/2, changed state to down
*Oct 27 13:42:01.676: %LINK-5-UPDOWN: Interface TenGigabitEthernet1/1/3, changed state to down
*Oct 27 13:42:01.677: %LINK-5-UPDOWN: Interface TenGigabitEthernet1/1/4, changed state to down
*Oct 27 13:42:01.677: %LINK-5-UPDOWN: Interface TenGigabitEthernet1/1/5, changed state to down
*Oct 27 13:42:01.678: %LINK-5-UPDOWN: Interface TenGigabitEthernet1/1/6, changed state to down
*Oct 27 13:42:01.680: %LINK-5-UPDOWN: Interface TenGigabitEthernet1/1/7, changed state to down
*Oct 27 13:42:01.680: %LINK-5-UPDOWN: Interface TenGigabitEthernet1/1/8, changed state to down
*Oct 27 13:42:01.680: %LINK-5-UPDOWN: Interface FortyGigabitEthernet1/1/1, changed state to down
*Oct 27 13:42:01.681: %LINK-5-UPDOWN: Interface FortyGigabitEthernet1/1/2, changed state to down
*Oct 27 13:42:01.683: %LINK-5-UPDOWN: Interface TwentyFiveGigE1/1/1, changed state to down
*Oct 27 13:42:01.683: %LINK-5-UPDOWN: Interface TwentyFiveGigE1/1/2, changed state to down
*Oct 27 13:42:02.079: %LINK-5-UPDOWN: Interface Vlan1, changed state to up
*Oct 27 13:42:02.672: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1/1, changed state to down
*Oct 27 13:42:02.673: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1/2, changed state to down
*Oct 27 13:42:02.674: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1/3, changed state to down
*Oct 27 13:42:02.674: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1/4, changed state to down
*Oct 27 13:42:02.674: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/1/1, changed state to down
*Oct 27 13:42:02.676: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/1/2, changed state to down
*Oct 27 13:42:02.677: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/1/3, changed state to down
*Oct 27 13:42:02.677: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/1/4, changed state to down
*Oct 27 13:42:02.677: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/1/5, changed state to down
*Oct 27 13:42:02.679: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/1/6, changed state to down
*Oct 27 13:42:02.679: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/1/7, changed state to down
*Oct 27 13:42:02.680: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/1/8, changed state to down
*Oct 27 13:42:02.681: %LINEPROTO-5-UPDOWN: Line protocol on Interface FortyGigabitEthernet1/1/1, changed state to down
*Oct 27 13:42:02.681: %LINEPROTO-5-UPDOWN: Line protocol on Interface FortyGigabitEthernet1/1/2, changed state to down
*Oct 27 13:42:02.683: %LINEPROTO-5-UPDOWN: Line protocol on Interface TwentyFiveGigE1/1/1, changed state to down
*Oct 27 13:42:02.684: %LINEPROTO-5-UPDOWN: Line protocol on Interface TwentyFiveGigE1/1/2, changed state to down
*Oct 27 13:42:02.925: %SYS-6-BOOTTIME: Time taken to reboot after reload = 276 seconds
*Oct 27 13:42:06.086: %PNP-6-PNP_BEST_UDI_UPDATE: Best UDI [PID:C9300-24UX,VID:A0,SN:FCW2308D060] identified via (master-registry)
*Oct 27 13:42:06.086: %PNP-6-PNP_CDP_UPDATE: Device UDI [PID:C9300-24UX,VID:A0,SN:FCW2308D060] identified for CDP
*Oct 27 13:42:06.107: %PNP-6-PNP_DISCOVERY_STOPPED: PnP Discovery stopped (Startup Config Present)
*Oct 27 13:42:06.285: ILP:: switch 1 POE mode : IEEE AT
*Oct 27 13:42:06.285: ILP:: POE POST detail for switch 1: PASS
*Oct 27 13:42:06.286: ILP:: Able to get POE POST from switch 1 MCU
*Oct 27 13:42:07.461: %HMANRP-6-EMP_NO_ELECTION_INFO: Could not elect active EMP switch, setting emp active switch to 0: EMP_RELAY: Could not elect switch with mgmt port UP
*Oct 27 13:42:12.151: %LINK-5-UPDOWN: Interface TenGigabitEthernet1/0/11, changed state to up
*Oct 27 13:42:13.170: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/0/11, changed state to up
*Oct 27 13:42:14.557: %LINK-5-UPDOWN: Interface AppGigabitEthernet1/0/1, changed state to up
*Oct 27 13:42:15.390: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Oct 27 13:42:15.557: %LINEPROTO-5-UPDOWN: Line protocol on Interface AppGigabitEthernet1/0/1, changed state to up
*Oct 27 13:42:16.076: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: CISCO_IDEVID_SUDI created succesfully
*Oct 27 13:42:16.080: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named CISCO_IDEVID_SUDI has been generated or imported by pki-sudi
*Oct 27 13:42:16.133: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: CISCO_IDEVID_SUDI0 created succesfully
*Oct 27 13:42:16.136: %PKI-2-NON_AUTHORITATIVE_CLOCK: PKI functions can not be initialized until an authoritative time source, like NTP, can be obtained.
*Oct 27 13:42:16.141: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: TEST_CISCO_IDEVID_SUDI created succesfully
*Oct 27 13:42:16.147: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named TEST_CISCO_IDEVID_SUDI has been generated or imported by pki-sudi
*Oct 27 13:42:16.181: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: TEST_CISCO_IDEVID_SUDI0 created succesfully
*Oct 27 13:42:16.183: %PKI-6-TRUSTPOINT_DELETE: Trustpoint: TEST_CISCO_IDEVID_SUDI deleted succesfully
*Oct 27 13:42:16.197: %CRYPTO_ENGINE-5-KEY_DELETED: A key named TEST_CISCO_IDEVID_SUDI has been removed from key storage
*Oct 27 13:42:16.198: %PKI-6-TRUSTPOINT_DELETE: Trustpoint: TEST_CISCO_IDEVID_SUDI0 deleted succesfully
*Oct 27 13:42:16.198: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: TEST_CISCO_IDEVID_SUDI created succesfully
*Oct 27 13:42:16.204: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named TEST_CISCO_IDEVID_SUDI has been generated or imported by pki-sudi
*Oct 27 13:42:16.219: %PKI-4-CSDL_COMPLIANCE_KEY_SIZE_WARNING: The key size 1024 is a weak key size used in a certificate under trustpoint TEST_CISCO_IDEVID_SUDI and will be deprecated
*Oct 27 13:42:16.222: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: TEST_CISCO_IDEVID_SUDI0 created succesfully
*Oct 27 13:42:16.224: %PKI-6-TRUSTPOINT_DELETE: Trustpoint: TEST_CISCO_IDEVID_SUDI deleted succesfully
*Oct 27 13:42:16.225: %CRYPTO_ENGINE-5-KEY_DELETED: A key named TEST_CISCO_IDEVID_SUDI has been removed from key storage
*Oct 27 13:42:16.225: %PKI-6-TRUSTPOINT_DELETE: Trustpoint: TEST_CISCO_IDEVID_SUDI0 deleted succesfully
*Oct 27 13:42:16.226: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: CISCO_IDEVID_CMCA2_SUDI created succesfully
*Oct 27 13:42:16.231: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named CISCO_IDEVID_CMCA2_SUDI has been generated or imported by pki-sudi
*Oct 27 13:42:16.263: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: CISCO_IDEVID_CMCA2_SUDI0 created succesfully
*Oct 27 13:42:16.265: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: CISCO_IDEVID_CMCA_SUDI created succesfully
*Oct 27 13:42:16.271: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named CISCO_IDEVID_CMCA_SUDI has been generated or imported by pki-sudi
*Oct 27 13:42:16.287: %PKI-4-CSDL_COMPLIANCE_KEY_SIZE_WARNING: The key size 1024 is a weak key size used in a certificate under trustpoint CISCO_IDEVID_CMCA_SUDI and will be deprecated
*Oct 27 13:42:16.289: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: CISCO_IDEVID_CMCA_SUDI0 created succesfully
*Oct 27 13:42:17.607: %PLATFORM_PM-6-FRULINK_INSERTED: 4x1G uplink module inserted in the switch 1 slot 1
*Oct 27 13:42:43.209: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
*Oct 27 13:43:01.143: %WSMAN-3-INVALID_TRUSTPOINT: Trustpoint associated with HTTP is either invalid or does not exist
Switch#
