11-06-2013 04:14 PM - edited 03-07-2019 04:28 PM
How do you do a factory reset from the console on a Cisco AIR-LAP1252AG-A-K9?
I have the password. Holding down the mode button while the access point is booting does not seem to do the trick.
Solved! Go to Solution.
11-08-2013 11:08 PM
It's looks like your AP is lwapp & try the below & see. Try the last two commands & see if that works. If not try with the first command as well.
AP0023.045e.df34#debug
AP0023.045e.df34#delete flash:private-multiple-fs
AP0023.045e.df34#reload
HTH
Rasika
**** Pls rate all useful responses ****
11-06-2013 06:47 PM
If it has a autonomous image you can try "write default-config" on the AP priviledge mode CLI.
If it has a lightweight image you can try "erase /all nvram:" on the AP priviledge mode CLI.
Mode button option & GUI option is described in this doc
http://www.cisco.com/en/US/docs/wireless/access_point/1250/installation/guide/125h_c3.html
HTH
Rasika
**** Pls rate all useful responses ****
11-08-2013 04:54 PM
That is not working. Here is the ouput.
IOS Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 3 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 2330624
flashfs[0]: Bytes available: 29538304
flashfs[0]: flashfs fsck took 14 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: 00:23:04:5e:df:34
Loading "flash:/c1250-rcvk9w8-mx/c1250-rcvk9w8-mx"...###########################
#######################################################
File "flash:/c1250-rcvk9w8-mx/c1250-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1250 Software (C1250-RCVK9W8-M), Version 12.4(10b)JA1, RELE
ASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Wed 30-Jan-08 12:11 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x003DD740
Initializing flashfs...
flashfs[1]: 3 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 31868928
flashfs[1]: Bytes used: 2330624
flashfs[1]: Bytes available: 29538304
flashfs[1]: flashfs fsck took 5 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
cisco AIR-LAP1252AG-A-K9 (PowerPC 8349) processor (revision A0) with 49142K/16
384K bytes of memory.
Processor board ID FTX123590E6
PowerPC 8349 CPU at 533Mhz, revision number 0x0031
Last reset from power-on
LWAPP image version 3.0.51.0
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:23:04:5E:DF:34
Part Number : 73-10425-05
PCA Assembly Number : 800-27630-05
PCA Revision Number : A0
PCB Serial Number : FOC12334VW4
Top Assembly Part Number : 800-29536-02
Top Assembly Serial Number : FTX123590E6
Top Revision Number : A0
Product/Model Number : AIR-LAP1252AG-A-K9
o
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar 1 00:00:06.975: %CDP_PD-4-POWER_OK: Full power - INJECTOR_DETECTED inline
power source
*Mar 1 00:00:06.979: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1250 Software (C1250-RCVK9W8-M), Version 12.4(10b)JA1, RELE
ASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Wed 30-Jan-08 12:11 by prod_rel_team
*Mar 1 00:00:07.939: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:08.939: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 00:00:26.983: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:27.131: Logging LWAPP message to 255.255.255.255.
%DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 10.0.7.
180, mask 255.255.255.0, hostname AP0023.045e.df34
Translating "CISCO-LWAPP-CONTROLLER.toltsg.com"...domain server (10.253.0.50)
%LWAPP-3-CLIENTEVENTLOG: Did not get vendor specific options from DHCP.
%LWAPP-3-CLIENTEVENTLOG: Did not get log server settings from DHCP.
%SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI init
iated
%LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER.to
ltsg.com
%LWAPP-3-CLIENTERRORLOG: DNS Name Lookup: could not resolve CISCO-LWAPP-CONTROLL
ER.toltsg.com
AP0023.045e.df34>en
Password:
AP0023.045e.df34#erase /all nvram
^
% Invalid input detected at '^' marker.
AP0023.045e.df34#write default-config
^
% Invalid input detected at '^' marker.
AP0023.045e.df34#
11-08-2013 11:08 PM
It's looks like your AP is lwapp & try the below & see. Try the last two commands & see if that works. If not try with the first command as well.
AP0023.045e.df34#debug
AP0023.045e.df34#delete flash:private-multiple-fs
AP0023.045e.df34#reload
HTH
Rasika
**** Pls rate all useful responses ****
12-30-2015 08:17 PM
All,
I have this problem. I have tried commands suggested by Rasika and also have tried MODE on AP. I am not able to factory reset configuration. I keep getting error message as below and am not able to configure AP.
*Mar 1 00:46:46.251: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:46:46.283: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:46:46.307: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
Not in Bound state.
*Mar 1 00:47:31.807: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:47:34.815: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:47:34.879: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.2.238, mask 255.255.255.0, hostname AP001e.f71a.ca2e
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: