Hi,
I am using ME3400 Switch for setting WDCMA for L2 switch config.
Packet Loss is trigger on RBS and collission detected. RBS setting for duplex is Full duplex and ME3400 switch duplex default : auto
I have try to change duplex setting on interface but error : Invalid input detected.
Below is my ME3400 version :
%Error parsing filename (Unknown error 0)
ME3400_BUNO01#show ver
Cisco IOS Software, ME340x Software (ME340x-METROACCESS-M), Version 12.2(50)SE4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Fri 26-Mar-10 09:46 by prod_rel_team
Image text-base: 0x01000000, data-base: 0x02300000
ROM: Bootstrap program is ME340x boot loader
BOOTLDR: ME340x Boot Loader (ME340x-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE (fc1)
ME3400_BUNO01 uptime is 2 days, 22 hours, 46 minutes
System returned to ROM by power-on
System restarted at 15:45:48 UTC Sun Sep 15 2013
System image file is "flash:/me340x-metroaccess-mz.122-50.SE4.bin"
cisco ME-3400G-12CS-D (PowerPC405) processor (revision D0) with 131072K bytes of memory.
Processor board ID FOC1346X4NJ
Last reset from power-on
6 Virtual Ethernet interfaces
16 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 64:16:8D:01:8C:00
Motherboard assembly number : 73-10630-08
Power supply part number : 341-0204-01
Motherboard serial number : FOC134644LQ
Power supply serial number : DTH13228098
Model revision number : D0
Motherboard revision number : A0
Model number : ME-3400G-12CS-D
Daughterboard assembly number : 73-10631-06
Daughterboard serial number : FOC13462XKL
System serial number : FOC1346X4NJ
Top Assembly Part Number : 800-27862-02
Top Assembly Revision Number : A0
Version ID : V02
CLEI Code Number : COMXF00ARA
Daughterboard revision number : A0
Second power supply part number : 341-0204-01
Second power supply serial number : DTH13228097
Hardware Board Revision Number : 0x03
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 16 ME-3400G-12CS-D 12.2(50)SE4 ME340x-METROACCESS-M
Configuration register is 0xF
ME3400_BUNO01#show int status
Port Name Status Vlan Duplex Speed Type
Gi0/1 connected trunk a-half a-100 10/100/1000BaseTX
Gi0/2 connected trunk a-half a-100 10/100/1000BaseTX
Gi0/3 disabled trunk auto auto Not Present
Gi0/4 disabled 1 auto auto Not Present
Gi0/5 disabled trunk auto auto Not Present
Gi0/6 disabled 1 auto auto Not Present
Gi0/7 disabled 1 auto auto Not Present
Gi0/8 disabled 1 auto auto Not Present
Gi0/9 disabled 1 auto auto Not Present
Gi0/10 disabled 1 auto auto Not Present
Gi0/11 disabled 1 auto auto Not Present
Gi0/12 disabled 1 auto auto Not Present
Gi0/13 notconnect 1 full 1000 1000BaseSX SFP
Gi0/14 notconnect 1 auto auto Not Present
Gi0/15 notconnect 1 auto auto Not Present
Gi0/16 notconnect 1 auto auto Not Present
ME3400_BUNO01(config)#interface gi0/1
ME3400_BUNO01(config-if)#duplex
^
% Invalid input detected at '^' marker.
ME3400_BUNO01(config-if)#duplex full
^
% Invalid input detected at '^' marke
Can some help me on this?
do i have to upgrade these switch?
What are the compatible version ?
