Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Bookmark
|
Subscribe
|

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Hi All,I have encounted an problem that currently has me stumped. I am trying to configure a 3750 switch with ipservices for use as a small localised test bed for wireless. what i am planning to implement is:1 x 3750 PoE switch with 3 vlans1 x WLC1 x...

lukedp by Level 1
  • 495 Views
  • 1 replies
  • 0 Helpful votes

HiI`m suddenly having problems with some static routes on a WS-C3750G-12S-E running 12.2(44)SE5.The routing table is really simple, only some static routes and a couple of VRFs. Gateway of last resort is 10.0.224.29 to network 0.0.0.0 10.0.0.0/16 is ...

perpaal by Level 1
  • 2313 Views
  • 6 replies
  • 0 Helpful votes

Hi,What's the method to perform password recover on a stack? I aleady have the standard procedure/link to perform on a single switch. Do I power down both members, disconnect the stack cables, then perform the procedure on the master, then power back...

lcaruso by Level 6
  • 2937 Views
  • 1 replies
  • 0 Helpful votes

Hello all,Newbie here and have been working on configuring a router and not having any luck getting ip's from it.Any help will greatly be appreciated....Current configuration : 3990 bytes!! Last configuration change at 01:06:48 PCTime Thu Aug 29 2013...

rrealy by Level 1
  • 913 Views
  • 2 replies
  • 0 Helpful votes

We just bought a 2960-C PD 8PT switch.The switch is delivered without powersupply. It is supposed to get power from a PoE port on another switch.When I connect the Gigabit 1 or 2 port on the 2960-C to a PoE port on my 4507 switch the 2960-C switch st...

torleif by Level 1
  • 5704 Views
  • 3 replies
  • 0 Helpful votes

I have two ME-3400EG-12CS-M switches.I was working using the console, suddenly the console of one (only one) of the switch start showing garbage.A telnet session to this switch works fine. Im using putty. 8 bits, 9600, parity none, flowcontrol none.I...

Just bought some IE2000 hardened switches and am wondering why the switch doesn't boot from the SDflash card similar to the IE3000/CGS2520 switches.I want to be able to swap out the switch, should it fail, with a new one and just take the sdflash car...

Hello,I have one switch that is auto-negotiating to 10 mbps (a-10) and I am curious as to why it is doing this. I have tried to separate laptops on two different ports and they keep negotiating to 10 mbps.Now I have another 3560 switch with the same ...

RGill94 by Level 1
  • 2673 Views
  • 6 replies
  • 0 Helpful votes

Each of the 4500X switches in our stack has a Fa1 interface next to the serial console port.  My understanding is that this is to be used for out-of-band management of the switch.  Here's the configuration of the interface:interface FastEthernet1vrf ...

Ok i have a strange one here.We currently have a switch stack with two 3750G-24PS switches. The past two times our 1252 AP's in local mode lost communication to the controller (scheduled reboot and Network loss), this one particular stack cause serie...

Hi,So here's my scenario:  I receive a bunch of different multicast feeds from seperate sources.  This is all sparse-mode multicast and each group of feeds has its own RP address.  To date, I've been managing the group-to-RP mappings using static ip ...

branfarm1 by Level 4
  • 727 Views
  • 1 replies
  • 0 Helpful votes

I'd put this on the getting started board, but it's too weird:I'm deploying to a site that will have a single ISP-assigned address. This connection will be used by users on the LAN for standard internet access, and by two dedicated multicast sources....

obi by Level 1
  • 1633 Views
  • 9 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card