cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
910
Views
1
Helpful
11
Replies

Cisco Nexus 9K - VPC config trouble-shooting

RG78874
Level 1
Level 1

Hello,

Background - Server connected using 10GB sfp from one slot, and another slot. This goes to the Cisco 9K. I've provided a working example that is VPC 6, and my other not working example VPC 19.

I need some help with my VPC's. VPC19 is not connecting on the same Switch, it has multiple VLANs and the other one has a single VLAN.

I've attached the configs that I am using. I've done some checks.

When I run the VPC Consistency Checksthey check out to match.

I've defaulted the port interface for Eth1/19 and added the config again.

I've even deleted the PO19 and added it again.

I'm at a limbo not sure what to do next.

Other servers are working, but I do not understand why I do not see as much detail on the VPC19 compared to VPC6 when running the consistency checks.

Both configs on both Switches output the same detail, I have done exactly the same steps on both Switches.

It just maybe something so simple.

I have tried creating the port first then the port channel, and vice versa but still no joy so i am reaching out. Thanks

 

2 Accepted Solutions

Accepted Solutions

M02@rt37
VIP
VIP

Hello @RG78874 

Same configuration regarding vPCs. So the only "difference" is the server. 

Check you lacp or bonding configuration on SERVER_NO2...mtu also...vlans allowed on Server Trunk port.

 

Best regards
.ı|ı.ı|ı. If This Helps, Please Rate .ı|ı.ı|ı.

View solution in original post

@RG78874 

EtherChannel is a technology used to combine multiple physical Ethernet links into a single logical link, offering increased bandwidth and redundancy. It can be configured in a static way: "On," which statically bundles ports without any negotiation protocol and requires matching configurations on both ends. LACP and PaGP are dynamic ways.

 

 

Best regards
.ı|ı.ı|ı. If This Helps, Please Rate .ı|ı.ı|ı.

View solution in original post

11 Replies 11

balaji.bandi
Hall of Fame
Hall of Fame

check MTU also remote vPC 19 from port-channel check is the Port-channel come up.

You have many VLAN are suspended, check the logs what is the reason of suspended

also suggest to remove lacp rate fast ( until you understand this correctly)

Also what is other side can able to match LACP capable ?

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Hi, I've added MTU to the config, why do i need need to do it again.

Remote VPC you mean Peer vpc, or what do you mean?

See the configuration difference, when you build vpc the configuration should match., if not they not going to form vPC ?

Both the vPC member should have identical configuration. as i was suggested on other post, remove vpc 19 on the port-channel configuration and see if the LACP come up ?

what is the end device connected to that vPC

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Check below 

MHM

Hi sorry change which mode to on?

@RG78874 

EtherChannel is a technology used to combine multiple physical Ethernet links into a single logical link, offering increased bandwidth and redundancy. It can be configured in a static way: "On," which statically bundles ports without any negotiation protocol and requires matching configurations on both ends. LACP and PaGP are dynamic ways.

 

 

Best regards
.ı|ı.ı|ı. If This Helps, Please Rate .ı|ı.ı|ı.

Hi friend' after make double check the config is correct

Can I see 

Show vpc breif <- from both vpc nexus 

Show lacp count 

Show lacp neighbor 

Thanks 

MHM

@MHM Cisco WorldThank you, but how would be the best way to unsuspend vlans from the vpc config?

Show vpc breif 

Give us some info if allow  vlan in PO in both NSK is same or not.

It can you allow some vlan in NSK1 and not allow it in NSK2

Show lacp count 

Give us some info about lacp exchange between server and nexus 

Lastly 

Show lacp neighbor 

Give us if the cable is connect to correct port or  not 

MHM

ok i'll have to get back to this once i get the right config, and i'll find out more on the server end.