06-06-2017 08:08 AM - edited 03-08-2019 10:52 AM
Hi folks,
I encounter a (very) strange behaviour with two compact switches 3560 CPD (WS-C3560CPD-8PT-S). Both are from the same batch, and have a serial starting by 'FOC1848xxxx'. They were purchased used. What I want is that devices are powered by their interfaces G0/9 & G0/10. We could expect that it works, but:
Here's below what I get from CLI, device(s) being powered by a 3560X-24P-S (PoE+, hence 30W per port), with and without brick:
C3560C#sh env all
(...)
PoE Power - Available:15.4(w) Backup:15.4(w)
Power Source Type Power(w) Mode
-------------- -------------- --------- ---------
A.C. Input Auxilliary 51(w) Available
Gi0/9 Type2 30(w) Back-up
Gi0/10 Type2 30(w) Back-up
(...)
Or, without brick:
C3560C#sh env all
(...)
PoE Power - Available:15.4(w) Backup:0.0(w)
Power Source Type Power(w) Mode
-------------- -------------- --------- ---------
Gi0/9 Type2 30(w) Available
Gi0/10 Type2 30(w) Available
Logged issue:
C3560C#sh log
(...)
Log Buffer (10240 bytes):
*Jan 2 02:00:36.705: %SYS-5-CONFIG_I: Configured from console by console
*Jan 2 02:00:51.500: %PDPSE-5-PWR_SRC_DISC: Power source change from Auxilliary Power + Gi0/9 + Gi0/10 to Gi0/9 + Gi0/10. Current power source is Gi0/9 + Gi0/10
*Jan 2 02:01:06.605: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan2, changed state to down
*Jan 2 02:01:07.596: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/5, changed state to down
*Jan 2 02:01:08.602: %LINK-3-UPDOWN: Interface GigabitEthernet0/5, changed state to down
*Jan 2 02:13:10.337: %PDPSE-5-PWR_SRC_DISC: Power source change from Gi0/9 + Gi0/10 to Auxilliary Power + Gi0/9 + Gi0/10. Current power source is Auxilliary Power
*Jan 2 02:13:17.919: %LINK-3-UPDOWN: Interface GigabitEthernet0/5, changed state to up
*Jan 2 02:13:18.920: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/5, changed state to up
*Jan 2 02:13:45.931: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan2, changed state to up
C3560C#sh cdp nei
(...)
Device ID Local Intrfce Holdtme Capability Platform Port ID
Switch Gig 0/10 172 S I WS-C3560X Gig 0/23
Switch Gig 0/9 137 S I WS-C3560X Gig 0/24
NWX02 Gig 0/5 147 S I WS-C2960C Gig 0/3
Total cdp entries displayed : 3
C3560C#
Of course, I have tried PoE powering with other devices, without any improvement (a 2960 PoE, and a 3560 compact PoE).
What I want is to power these devices without any power brick, in a remote location. So, if ever you have any idea, it is very welcome - since I'm really stuck on that behaviour.
Thanks in advance for your help!
06-09-2017 12:48 AM
Bump!
I know that this is a very strange behaviour, but if someone (a Cisco representative, maybe ?) has an idea, this would be welcome.
Thanks!
06-13-2017 01:33 AM
Bump again :)
Thanks!
06-15-2017 04:18 AM
Bump again. Do I have to turn to Aruba devices instead of Cisco ?
11-15-2018 12:00 PM
William,
I have the same issue with this device and its not clear why...Did you ever get an answer?
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: