cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
6872
Views
0
Helpful
21
Replies

Csico C2960-XR stack down state

Yuliya S
Level 1
Level 1

Hi guys.

 

I have two switches:

WS-C2960XR-48TS-I

WS-C2960XR-24PS-I 

 

I tried to stack these switches. I connected port 1 of SW1 to port 2 of SW2 and port  2 of SW1 

then i configured a priority and stack-mac persistent timer 4:

sw1

Switch/Stack Mac Address : 38ed.1848.4400
Mac persistency wait time: 4 mins
                                           H/W   Current
Switch#  Role   Mac Address     Priority Version  State 
----------------------------------------------------------
*1       Master 38ed.1848.4400     1      4       Ready               

 

         Stack Port Status             Neighbors     
Switch#  Port 1     Port 2           Port 1   Port 2 
--------------------------------------------------------
  1       Down       Down             None     None

 

 

sw2

Switch#show switch det
Switch/Stack Mac Address : f0b2.e5fd.3380
Mac persistency wait time: 4 mins
                                           H/W   Current
Switch#  Role   Mac Address     Priority Version  State 
----------------------------------------------------------
*2       Master f0b2.e5fd.3380     2      4       Ready               

 

         Stack Port Status             Neighbors     
Switch#  Port 1     Port 2           Port 1   Port 2 
--------------------------------------------------------
  2       Down       Down             None     None

Switch#

 

Software version is same for both switches: 

Cisco IOS Software, C2960X Software (C2960X-UNIVERSALK9-M), Version 15.0(2a)EX5, RELEASE SOFTWARE (fc3)

Then i reloaded two switches at the some time but i see the state of both port is DOWN, could you help me?

 

 

1 Accepted Solution

Accepted Solutions

sorry, I see you found the data sheet also.   I am out of ideas.  It should be working.

Can you post the full show version of both switches ?

View solution in original post

21 Replies 21

Mark Malone
VIP Alumni
VIP Alumni

Hi can you post show switch stack-ports

Have you tried to reseat the stack cables this can help, also shut both down start up the master wait 30 secs and then start the slave in case there having an issue negotiating

 

You could move off those EX IOS as well there known to be quite buggy , I see in your release notes a bug that may effect you and theres a few more stack bugs too

http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960x/software/15-0_2_EX/release_notes/OL30810.html

  • CSCun41300

 

Unsetting the stack member numbers and then rebooting the switch stack can cause the stack to crash or cause the stack master election to stop.

If this occurs, either:

Restart the switch stack.

Manually assign stack member numbers to all switches in the stack, and then restart the stack.

 

Hi Mark!

I upgraded the soft of both switches till version 15.2(3)E2, RELEASE SOFTWARE (fc1)

can you post show switch stack-ports

Yes, i can, see the output below:

Switch#show swit stack-ports 
  Switch #    Port 1       Port 2 
  --------    ------       ------ 
    1          Down         Down  

 

Have you tried to reseat the stack cables this can help, also shut both down start up the master wait 30 secs and then start the slave in case there having an issue negotiating

Yes, I have tried to reseat the stack cables but it doesn't help me.

See logs:

Sep 17 03:27:57.258:  Flexstack module is 1 
Sep 17 03:31:01.060: %STACKMGR-4-SWITCH_ADDED: Switch 1 has been ADDED to the stack
Sep 17 03:31:02.391: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
Sep 17 03:31:02.395: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
Sep 17 03:31:04.370: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
Sep 17 03:31:09.609: %LINK-5-CHANGED: Interface FastEthernet0, changed state to administratively down
Sep 17 03:31:09.993: %SYS-5-CONFIG_I: Configured from memory by console
Sep 17 03:31:10.165: %STACKMGR-5-SWITCH_READY: Switch 1 is READY
Sep 17 03:31:10.165: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 1 has changed to state DOWN
Sep 17 03:31:10.165: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 2 Switch 1 has changed to state DOWN
Sep 17 03:31:10.567: %STACKMGR-5-MASTER_READY: Master Switch 1 is READY
Sep 17 03:31:10.570: %PLATFORM-6-FLEXSTACK_INSERTED: FlexStack module inserted in Switch 1.
Sep 17 03:31:11.063: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
Sep 17 03:31:11.108: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2960X Software (C2960X-UNIVERSALK9-M), Version 15.2(3)E2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Tue 21-Jul-15 12:50 by prod_rel_team
Sep 17 03:31:11.203: %SSH-5-ENABLED: SSH 1.99 has been enabled
Sep 17 03:31:11.986: %LINK-5-CHANGED: Interface Vlan1, changed state to administratively down
Sep 17 03:31:12.489: %USB_CONSOLE-6-MEDIA_USB: Console media-type is USB.
Sep 17 03:31:13.157: %PLATFORM_ENV-6-FRU_PS_OIR: FRU Power Supply 1 inserted but powered off
Sep 17 03:31:13.216: %PLATFORM_ENV-6-FRU_PS_OIR: FRU Power Supply 2 inserted
Sep 17 03:31:15.834: %PLATFORM_ENV-1-FAN_NOT_PRESENT: Fan is not present 

hi Yulia,

If possible ... try connecting port 1 and 2 on the same switch.  The ports should show as coming up.  This will confirm if you have a problem with the ports or with the cables.

 

Regards,

Doron

 

Tried to connect port 1 and 2 on the same switch - all is ok for both switches:

Sep 17 04:47:35.882: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 2 has changed to state UP
Sep 17 04:47:35.882: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 2 Switch 2 has changed to state UP

 

Switch#show switch stack-ports
  Switch #    Port 1       Port 2
  --------    ------       ------
    1           Ok           Ok

Returned cables - doesn't work 

One more thing ... I think your switches are running IP lite which does not support stacking.

 

Look at the show version or show license to confirm which license you have enabled.

Should i buy license for that? may be i'm using incorrect software image?

 

Switch#show license
Index 1 Feature: iplite
        Period left: Life time
        License Type: Permanent
        License State: Active, In Use
        License Priority: Medium
        License Count: Non-Counted

I see that 2960XR ip lite supports FlexStack (see table 5)

http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-2960-x-series-switches/data_sheet_c78-728232.html#Table52960XRDefaultSupplyCo

 

Actually IP Lite on the XR switches does support stacking.  See table 5 and 6 from the data sheet here.

 

http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-2960-x-series-switches/data_sheet_c78-728232.html

sorry, I see you found the data sheet also.   I am out of ideas.  It should be working.

Can you post the full show version of both switches ?

See show ver below

 

1st sw:

Switch#show ver
Cisco IOS Software, C2960X Software (C2960X-UNIVERSALK9-M), Version 15.2(3)E2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Tue 21-Jul-15 12:50 by prod_rel_team

ROM: Bootstrap program is C2960X boot loader
BOOTLDR: C2960X Boot Loader (C2960X-HBOOT-M) Version 15.0(2r)EX4, RELEASE SOFTWARE (fc1)

Switch uptime is 7 minutes
System returned to ROM by power-on
System restarted at 05:39:39 UTC Thu Sep 17 2015
System image file is "flash:/c2960x-universalk9-mz.152-3.E2/c2960x-universalk9-mz.152-3.E2.bin"
Last reload reason: Reload command

 

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco WS-C2960XR-24PS-I (APM86XXX) processor (revision H0) with 524288K bytes of memory.
Processor board ID FDO1927I0A5
Last reset from reload command
1 Virtual Ethernet interface
1 FastEthernet interface
80 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address       : 38:ED:18:48:44:00
Motherboard assembly number     : 73-15379-03
Power supply part number        : 341-0531-02
Motherboard serial number       : FDO192704UC
Power supply serial number      : LIT192118J1
Model revision number           : H0
Motherboard revision number     : A0
Model number                    : WS-C2960XR-24PS-I
Daughterboard assembly number   : 73-14200-03
Daughterboard serial number     : FDO19260FBL
System serial number            : FDO1927I0A5
Top Assembly Part Number        : 68-5014-03
Top Assembly Revision Number    : A0
Version ID                      : V03
CLEI Code Number                : CMMRY10ARA
Daughterboard revision number   : A0
Hardware Board Revision Number  : 0x06


Switch Ports Model                     SW Version            SW Image
------ ----- -----                     ----------            ----------
*    2 28    WS-C2960XR-24PS-I         15.2(3)E2             C2960X-UNIVERSALK9-M


Configuration register is 0xF

 

 

 

2nd SW

 

 

Switch#show ver
Cisco IOS Software, C2960X Software (C2960X-UNIVERSALK9-M), Version 15.2(3)E2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Tue 21-Jul-15 12:50 by prod_rel_team

ROM: Bootstrap program is C2960X boot loader
BOOTLDR: C2960X Boot Loader (C2960X-HBOOT-M) Version 15.0(2r)EX4, RELEASE SOFTWARE (fc1)

Switch uptime is 9 minutes
System returned to ROM by power-on
System restarted at 05:39:01 UTC Thu Sep 17 2015
System image file is "flash:/c2960x-universalk9-mz.152-3.E2/c2960x-universalk9-mz.152-3.E2.bin"
Last reload reason: Reload command

 

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco WS-C2960XR-48TS-I (APM86XXX) processor (revision H0) with 524288K bytes of memory.
Processor board ID FDO1929I0AE
Last reset from reload command
1 Virtual Ethernet interface
1 FastEthernet interface
80 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address       : F0:B2:E5:FD:33:80
Motherboard assembly number     : 73-15380-03
Power supply part number        : 341-0530-02
Motherboard serial number       : FDO19250NZ3
Power supply serial number      : DCB1925D0MV
Model revision number           : H0
Motherboard revision number     : A0
Model number                    : WS-C2960XR-48TS-I
Daughterboard assembly number   : 73-14200-03
Daughterboard serial number     : FDO19261PS2
System serial number            : FDO1929I0AE
Top Assembly Part Number        : 68-5015-03
Top Assembly Revision Number    : A0
Version ID                      : V03
CLEI Code Number                : CMMRU10ARA
Daughterboard revision number   : A0
Hardware Board Revision Number  : 0x06


Switch Ports Model                     SW Version            SW Image
------ ----- -----                     ----------            ----------
*    1 52    WS-C2960XR-48TS-I         15.2(3)E2             C2960X-UNIVERSALK9-M


Configuration register is 0xF