I have a 3845.
When I do a "show inventory" i see:
Admin-3845#show inventory
NAME: "3845 chassis", DESCR: "3845 chassis"
PID: CISCO3845 , VID: V01 , SN: FTX12
NAME: "c3845 Motherboard with Gigabit Ethernet on Slot 0", DESCR: "c3845 Motherboard with Gigabit Ethernet"
PID: CISCO3845-MB , VID: V07 , SN: FOC12
NAME: "PVDMII DSP SIMM with four DSPs on Slot 0 SubSlot 4", DESCR: "PVDMII DSP SIMM with four DSPs"
PID: PVDM2-64 , VID: V01 , SN: FOC12
NAME: "PVDMII DSP SIMM with four DSPs on Slot 0 SubSlot 5", DESCR: "PVDMII DSP SIMM with four DSPs"
PID: PVDM2-64 , VID: V01 , SN: FOC12
NAME: "High Density Voice2 Network module with on board two port interface on Slot 1", DESCR: "High Density Voice2 Network module with on board two port interface "
PID: NM-HDV2-2T1/E1 , VID: V05 , SN: FOC12
NAME: "PVDMII DSP SIMM with four DSPs on Slot 1 SubSlot 2", DESCR: "PVDMII DSP SIMM with four DSPs"
PID: PVDM2-64 , VID: V01 , SN: FOC12
NAME: "PVDMII DSP SIMM with four DSPs on Slot 1 SubSlot 3", DESCR: "PVDMII DSP SIMM with four DSPs"
PID: PVDM2-64 , VID: V01 , SN: FOC12
NAME: "High Density Voice2 Network module with on board two port interface on Slot 2", DESCR: "High Density Voice2 Network module with on board two port interface "
PID: NM-HDV2-2T1/E1 , VID: V05 , SN: FOC12
NAME: "PVDMII DSP SIMM with four DSPs on Slot 2 SubSlot 2", DESCR: "PVDMII DSP SIMM with four DSPs"
PID: PVDM2-64 , VID: V01 , SN: FOC12
NAME: "PVDMII DSP SIMM with four DSPs on Slot 2 SubSlot 3", DESCR: "PVDMII DSP SIMM with four DSPs"
PID: PVDM2-64 , VID: V01 , SN: FOC12
Admin-3845#
From this information I can see i have 6 x PVDM2-64 modules. 2 on each NM-HDV2-2T1/E1 and 2 on the motherboard. Correct?
Here is my running config:
!
isdn switch-type primary-ni
!
voice-card 0
dsp services dspfarm
!
voice-card 1
!
voice-card 2
!
!
controller T1 1/0
pri-group timeslots 1-24 service mgcp
description ***ATT
!
controller T1 1/1
!
controller T1 2/0
clock source internal
pri-group timeslots 1-24 service mgcp
description ***ATT
!
controller T1 2/1
!
dspfarm profile 10 conference
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 16
associate application SCCP
Why am I only allowed to have a max sessions of 16 on profile 10? Why can't I add another profile doing transcoding? It gives me <0-0> when I type "maximum sessions ?".
Thanks for any help,
JJ