08-15-2012 11:46 PM - edited 03-07-2019 08:22 AM
Hi Team,
I am trying to setup WS-SVC-WISM2-K9 on cisco 6509 switch with IOS version 12.2(33)SXJ1.
I have completed the below config and seeing service-port up but not coming in oper-up status.
I have installed WiSM module in slot 8 and seeing TG8/1, T8/2,G8/3 and G8/4 switch ports under module 8.
I am seeing only the automatically created port-channel 415 up with only T8/1 in it which strange to me.
I cant modify those interfaces as seeing error " These interfaces can not be modified.
Please provide suggestion about wht could be the wrong here?
COR-01#sh wism status
Service Vlan : 93, Service IP Subnet : 1.1.1.1/255.255.255.0
WLAN
Slot Controller Service IP Management IP SW Version Controller Type Status
----+-----------+----------------+----------------+------------+------------------+---------------
8 1 0.0.0.0 0.0.0.0 WS-SVC-WISM-2-K9 Service Port Up
JP2-RDC-COR-01#sh wism module 8 controller 1 status
WiSM Controller 1 in Slot 8 configured with auto-lag
Operational Status of the Controller : Service Port Up
Service VLAN : 93
Service Port : 3
Service Port Mac Address : 30e4.db38.9981
Service IP Address : 0.0.0.0
Management IP Address : 0.0.0.0
Software Version :
Port Channel Number : 415
Allowed-vlan list : 90,800,810
Native VLAN ID : 90
WCP Keep Alive Missed : 0
JP2-RDC-COR-01#sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL16084N3K
2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL16085AEH
3 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL16159JHP
4 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL16085099
5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1550Y2C7
8 4 WiSM 2 WLAN Service Module WS-SVC-WISM2-K9 SAL16159DWW
9 16 CEF720 16 port 10GBaseT WS-X6716-10T SAL1626F9HR
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 c464.1305.b274 to c464.1305.b2a3 4.2 12.2(18r)S1 12.2(33)SXJ1 Ok
2 c464.1387.f5b4 to c464.1387.f5e3 4.2 12.2(18r)S1 12.2(33)SXJ1 Ok
3 5057.a866.6c98 to 5057.a866.6cc7 4.2 12.2(18r)S1 12.2(33)SXJ1 PwrDown
4 f0f7.556a.2bc0 to f0f7.556a.2bef 4.2 12.2(18r)S1 12.2(33)SXJ1 PwrDown
5 5475.d07b.62d0 to 5475.d07b.62d7 4.1 8.5(4) 12.2(33)SXJ1 Ok
8 0007.7d8c.5390 to 0007.7d8c.539f 1.1 12.2(18r)S1 12.2(33)SXJ1 Ok
9 442b.034f.7410 to 442b.034f.741f 2.1 12.2(18r)S1 12.2(33)SXJ1 Ok
TenGigabitEthernet8/1 unassigned YES unset up up
TenGigabitEthernet8/2 unassigned YES unset down down
GigabitEthernet8/3 unassigned YES unset up up
GigabitEthernet8/4 unassigned YES unset administratively down down
COR-01(config)#int g8/4
% This interface cannot be modified
Version 12.2(33)SXJ1
ip dhcp excluded-address 1.1.1.1
!
ip dhcp pool WiSM_service_Port
host 1.1.1.2 255.255.255.0
hardware-address 30e4.db38.a8c1
wism service-vlan 93
wism module 8 controller 1 allowed-vlan 90,800,810
wism module 8 controller 1 native-vlan 90
interface Vlan93
description WiSM service port do not route-Inner Chassis WiSM to Supervisor connection
ip address 1.1.1.1 255.255.255.0
COR-01#sh etherchannel summary
415 Po415(SU) - Te8/1(P)
08-16-2012 03:52 PM
Your Service Port VLAN (93) is NOT ALLOWED.
08-16-2012 07:46 PM
I have tried allowing vlan 93 but didnt work. I ahve run debug wism events on Cat6509 and seeing below logs:
Aug 17 02:44:26.035: WiSM-Evt:dman_show_module_status: Port Channel in the hwidb/fec goup is :1/415
Aug 17 02:44:26.799: WiSM-Evt:dman_cntrl_db_search_by_mac: Found mac 30e4.db38.9981 for slot/port 8/1
Aug 17 02:44:26.799: WiSM-Evt:dman_reg_arp_added: cntrl 8/1 got an ip 1.1.1.3 30e4.db38.9981/30e4.db38.9981
Aug 17 02:44:26.799: WiSM-Evt:dman_reg_arp: received a garp from 1.1.1.3/1.1.1.3
Aug 17 02:44:26.799: WiSM-Evt:dman_cntrl_db_search_by_mac: Found mac 30e4.db38.9981 for slot/port 8/1
Aug 17 02:44:26.799: WiSM-Evt:dman_reg_arp_added: cntrl 8/1 got an ip 1.1.1.3 30e4.db38.9981/30e4.db38.9981
Aug 17 02:44:40.019: WiSM-Evt:dman_reg_arp: received a garp from 1.1.1.2/1.1.1.2
Aug 17 02:44:42.127: WiSM-Evt:dman_proc_keepalive_tmr_handler: keepalive timer expired for 8/1
Aug 17 02:44:42.127: WiSM-Evt:dman_cntrl_db_search: something wrong 15
WiSM Controller 1 in Slot 8 configured with auto-lag
Operational Status of the Controller : Started KeepAlive
Service VLAN : 93
Service Port : 3
Service Port Mac Address : 30e4.db38.9981
Service IP Address : 1.1.1.3
Management IP Address : 0.0.0.0
Software Version :
Port Channel Number : 415
Allowed-vlan list : 90,93,800,810
Native VLAN ID : 90
WCP Keep Alive Missed : 0
08-16-2012 07:55 PM
Can you please post the output to the command "sh run | i wism module 8 controller 1"?
08-16-2012 07:59 PM
COR-01#sh run | inc wism module 8 controller 1
wism module 8 controller 1 allowed-vlan 90,93,800,810
wism module 8 controller 1 native-vlan 90
08-16-2012 08:03 PM
Forgot to ask if you can also post the output to the command "sh wism module 8 controller 1 status".
08-16-2012 08:13 PM
COR-01#sh wism module 8 controller 1 status
WiSM Controller 1 in Slot 8 configured with auto-lag
Operational Status of the Controller : Started KeepAlive
Service VLAN : 93
Service Port : 3
Service Port Mac Address : 30e4.db38.9981
Service IP Address : 1.1.1.3
Management IP Address : 0.0.0.0
Software Version :
Port Channel Number : 415
Allowed-vlan list : 90,93,800,810
Native VLAN ID : 90
WCP Keep Alive Missed : 0
Also providing Controller interface summary output. I have not used DHCP here. Assigned static ips.
(Cisco Controller) >show interface summary
Interface Name Port Vlan Id IP Address Type Ap Mgr Guest
-------------------------------- ---- -------- --------------- ------- ------ -----
management LAG untagged 10.76.12.12 Static Yes No
service-port N/A N/A 1.1.1.3 Static No No
virtual N/A N/A 2.2.2.2 Static No No
08-16-2012 08:53 PM
I cant modify those interfaces as seeing error " These interfaces can not be modified.
You are not allowed to modify the etherchannel ports. It's normal.
If you need to, you can only console into the WiSM 2 or you use the command to session in: session slot 8 process 1
Command needs to be run in the 6500.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide