03-05-2024 10:28 PM
Hi
If get command show interface vlan 3
Vlan 3 has layer 3 vlan and Have traffic
For nexus in prtg cacti zabbix Donnot able to get Graphs Form VLANS
Any idea For Solve this ?
Solved! Go to Solution.
03-06-2024 12:02 AM
what version of nexus, what SNMP version you using ?
if this is Layer3 VLAN with IP address, most of the NMS can monitor that VLAN Traffic (but default the VLAN SVI set to 1GB only, so if the traffic going more than that you get warning, you need to increase VLAN Interface bandwidth to fix that)
03-06-2024 12:02 AM
what version of nexus, what SNMP version you using ?
if this is Layer3 VLAN with IP address, most of the NMS can monitor that VLAN Traffic (but default the VLAN SVI set to 1GB only, so if the traffic going more than that you get warning, you need to increase VLAN Interface bandwidth to fix that)
03-06-2024 11:12 PM
Version 2 traffic under 1G
03-07-2024 01:04 AM
Version 2 traffic under 1G
before snmp get any data, you should see first on cli what kind of packet in and out, as i showed the output.
not sure is this bug at this stage, as suggested try increasing vlan interface bandwidth to more and issue show interface vlanx see you able to see the packets
03-06-2024 12:20 AM - edited 03-09-2024 12:26 AM
admin@atrinnet.net wrote:Hi
If get command show interface vlan 3
Vlan 3 has layer 3 vlan and Have traffic
For nexus in prtg cacti zabbix Donnot able to get Graphs Form VLANS
Any idea For Solve this how to stops
Use debugging and troubleshooting tools provided by the monitoring platforms to diagnose any issues with VLAN monitoring. Check for error messages, SNMP queries, and data collection processes to identify any potential problems.
03-06-2024 03:03 AM
Vlan244 is up, line protocol is up, autostate enabled
Hardware is EtherSVI, address is 003a.7d96.6f55
Description: Ramin Test
Internet Address is 172.18.14.1/30
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 255/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not supported
ARP type: ARPA
Last clearing of "show interface" counters never
L3 in Switched:
ucast: 0 pkts, 0 bytes
L3 out Switched:
ucast: 0 pkts, 0 byte
VLAN have 300mbps traffic on access port
CLi and graph donnot show me any tarffic
03-06-2024 09:24 AM
we have many nexus 7K we do not see that issue at all :
show interface vlan 100
Vlan100 is up, line protocol is up, autostate enabled
reliability 255/255, txload 5/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not supported
ARP type: ARPA
Last clearing of "show interface" counters never
60 seconds input rate 4155842 bits/sec, 1706 packets/sec
60 seconds output rate 19646895 bits/sec, 3768 packets/sec
Load-Interval #2: 5 minute (300 seconds)
input rate 4.58 Mbps, 1.63 Kpps; output rate 24.65 Mbps, 4.32 Kpps
L3 Switched:
input: 25650833801 pkts, 8239095704432 bytes - output: 67440586761 pkts, 47048774196351 bytes
L3 in Switched:
ucast: 25637394456 pkts, 8237713535406 bytes - mcast: 13439345 pkts, 1382169026 bytes
L3 out Switched:
ucast: 67440586761 pkts, 47048774196351 bytes - mcast: 0 pkts, 0 bytes
i see your TX load full : ( try increase the bandwidth on SVI and monitor)
reliability 255/255, txload 255/255, rxload 1/255
or this could be bug :
https://quickview.cloudapps.cisco.com/quickview/bug/CSCvp32970
03-06-2024 11:07 PM
cisco Nexus9000 C9396PX Chassis
nxos.9.3.12.bin
Donnot work
03-06-2024 11:11 PM
show interface vlan 236
Vlan236 is up, line protocol is up, autostate enabled
Hardware is EtherSVI, address is 74a2.e6e7.f677
Internet Address is IPVALID-OF-VLAN/27
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 173/255, rxload 169/255
Encapsulation ARPA, loopback not set
Keepalive not supported
ARP type: ARPA
Last clearing of "show interface" counters never
L3 in Switched:
ucast: 0 pkts, 0 bytes
L3 out Switched:
ucast: 0 pkts, 0 bytes
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide