Hardware compatibility for Supervisor 2T

[Sri v]

i have a cisco 6509-E chassis with VS-SUP2T-10G with VS-F6K-MSFC5;VS-F6K-MSFC5.. does it support WS-X6716-10G-3C & WS-X6716-10G-3CXL ?

Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL1203DEJL
4 24 CEF720 24 port 1000mb SFP WS-X6824-SFP SAL1826VJ4G
5 5 Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G SAL1825UZQ4

Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 001e.be82.39bc to 001e.be82.39d3 3.1 12.2(18r)S1 15.1(2)SY2 Ok
4 d072.dcfe.6f30 to d072.dcfe.6f47 2.3 12.2(18r)S1 15.1(2)SY2 Ok
5 503d.e514.001a to 503d.e514.0021 2.1 12.2(50r)SYS 15.1(2)SY2 Ok

Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 Centralized Forwarding Card WS-F6700-CFC SAL1203DA99 4.0 Ok
4 Distributed Forwarding Card WS-F6K-DFC4-A SAL1826VJ4G 2.3 Ok
5 Policy Feature Card 4 VS-F6K-PFC4 SAL1825V8LE 2.1 Ok
5 CPU Daughterboard VS-F6K-MSFC5 SAL1824UUDC 3.0 Ok

[Mark Malone]

You need a different daughter card as below

http://www.cisco.com/c/en/us/products/collateral/interfaces-modules/catalyst-6500-series-supervisor-engine-2t/data_sheet_c78-648214.html

Table 5. Product Specifications

Product	Specifications
Chassis compatibility	• E-Series only: Cisco Catalyst 6503-E, 6504-E, 6506-E, 6509-E, 6509-V-E, 6513E
Switch fabric	• 2.08 Tbps Crossbar Switch Fabric with 26 Fabric Channels
Line-card compatibility	• WS-X6908-10G-2T, WS-X6908-10G-2TXL • WS-X6824-SFP-2T, WS-X6824-SFP-2TXL • WS-X6848-SFP-2T, WS-X6848-SFP-2TXL • WS-X6848-TX-2T, WS-X6848-TX-2TXL • WS-X6816-10T-2T, WS-X6816-10T-2TXL • WS-X6816-10G-2T, WS-X6816-10G-2TXL • WS-X6904-40G-2T, WS-X6904-40G-2TXL • WS-X6704-10GE with CFC • WS-X6724-SFP with CFC • WS-X6748-SFP with CFC • WS-X6748-GE-TX with CFC • WS-X6148A-RJ-45, WS-X6148A-45AF, WS-X6148-FE-SFP, WS-X6148A-GE-TX, WS-X6148A-GE-45AF, WS-X6148E-GE-45AT With a DFC4 or DFC4XL upgrade (WS-F6k-DFC4-A, WS-F6k-DFC4-AXL) • WS-X6704-10GE • WS-X6724-SFP • WS-X6748-SFP • WS-X6748-GE-TX With a DFC4 or DFC4XL upgrade (WS-F6k-DFC4-E, WS-F6k-DFC4-EXL) • WS-X6716-10G-3C, WS-X6716-10G-3CXL • WS-X6716-10T-3C, WS-X6716-10T-3CXL

[Sri v]

Hi Mark,

Thanks for the response

so u suggesting me to go for the below linecards as it will support with my supervisor?

• WS-X6716-10G-3C, WS-X6716-10G-3CXL

• WS-X6716-10T-3C, WS-X6716-10T-3CXL

Because supervisor running with PFC4 and one linecard already running with DFC-A

[Mark Malone · Accepted solution]

Yes the DFC4-A will support those cards doc attached , I didn't see you had the dfc4 in original post

[Sri v]

Thanks mark..

Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
5 5 Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G SAL1825UZQ4

Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
5 503d.e514.001a to 503d.e514.0021 2.1 12.2(50r)SYS 15.1(2)SY2 Ok

Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
5 Policy Feature Card 4 VS-F6K-PFC4 SAL1825V8LE 2.1 Ok
5 CPU Daughterboard VS-F6K-MSFC5 SAL1824UUDC 3.0 Ok