06-10-2015 11:05 PM - edited 03-08-2019 12:30 AM
Hi, we have these commands configured in a 6500 but we dont understand what these commands do, and it shows a warning if i try to delete them (cos-map)
interface GigabitEthernet1/18
description ENLACE
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 800,801,900,901
switchport mode trunk
load-interval 30
wrr-queue cos-map 2 1 1 2
wrr-queue cos-map 3 5 3 4
wrr-queue cos-map 3 7 6 7
rcv-queue cos-map 1 2 1
rcv-queue cos-map 1 3 2
rcv-queue cos-map 1 4 3
rcv-queue cos-map 1 5 4
rcv-queue cos-map 1 6 5
rcv-queue cos-map 1 7 6
rcv-queue cos-map 1 8 7
thanks
06-10-2015 11:13 PM
I have this config but its quite hard to undertand this exit...
#show queueing interface g1/18
Interface GigabitEthernet1/18 queueing strategy: Weighted Round-Robin
Port QoS is enabled
Trust boundary disabled
Port is untrusted
Extend trust state: not trusted [COS = 0]
Default COS is 0
Queueing Mode In Tx direction: mode-cos
Transmit queues [type = 1p3q8t]:
Queue Id Scheduling Num of thresholds
-----------------------------------------
01 WRR 08
02 WRR 08
03 WRR 08
04 Priority 01
WRR bandwidth ratios: 100[queue 1] 150[queue 2] 200[queue 3]
queue-limit ratios: 50[queue 1] 20[queue 2] 15[queue 3] 15[Pri Queue]
queue tail-drop-thresholds
--------------------------
1 70[1] 100[2] 100[3] 100[4] 100[5] 100[6] 100[7] 100[8]
2 70[1] 100[2] 100[3] 100[4] 100[5] 100[6] 100[7] 100[8]
3 100[1] 100[2] 100[3] 100[4] 100[5] 100[6] 100[7] 100[8]
queue random-detect-min-thresholds
----------------------------------
1 40[1] 70[2] 70[3] 70[4] 70[5] 70[6] 70[7] 70[8]
2 40[1] 70[2] 70[3] 70[4] 70[5] 70[6] 70[7] 70[8]
3 70[1] 70[2] 70[3] 70[4] 70[5] 70[6] 70[7] 70[8]
queue random-detect-max-thresholds
----------------------------------
1 70[1] 100[2] 100[3] 100[4] 100[5] 100[6] 100[7] 100[8]
2 70[1] 100[2] 100[3] 100[4] 100[5] 100[6] 100[7] 100[8]
3 100[1] 100[2] 100[3] 100[4] 100[5] 100[6] 100[7] 100[8]
WRED disabled queues:
queue thresh cos-map
---------------------------------------
1 1 0
1 2
1 3
1 4
1 5
1 6
1 7
1 8
2 1 1 2
2 2
2 3
2 4
2 5
2 6
2 7
2 8
3 1
3 2
3 3
3 4
3 5 3 4
3 6
3 7 6 7
3 8
4 1 5
Queueing Mode In Rx direction: mode-cos
Receive queues [type = 1q8t]:
Queue Id Scheduling Num of thresholds
-----------------------------------------
01 WRR 08
WRR bandwidth ratios: 100[queue 1]
queue-limit ratios: 100[queue 1]
queue tail-drop-thresholds
--------------------------
1 100[1] 100[2] 100[3] 100[4] 100[5] 100[6] 100[7] 100[8]
queue thresh cos-map
---------------------------------------
1 1 0 1 2 3 4 5 6 7
1 2
1 3
1 4
1 5
1 6
1 7
1 8
Packets dropped on Transmit:
BPDU packets: 0
queue dropped [cos-map]
---------------------------------------------
1 0 [0 ]
2 0 [1 2 ]
3 0 [3 4 6 7 ]
4 0 [5 ]
Packets dropped on Receive:
BPDU packets: 0
queue dropped [cos-map]
---------------------------------------------
1 0 [0 1 2 3 4 5 6 7 ]
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide