How to configure link between 2921 and SM-D-ES3G-48-P EtherSwitch Service Module

ogor · ‎09-15-2012

hi,

I can't do that like the procedure given by Cisco.

http://www.cisco.com/en/US/partner/docs/routers/access/interfaces/software/feature/guide/eesm_sw.html#wp1942894

Cisco Procedure :

interface gi10/0

ip address x.x.x.x x.x.x.x

service-module gigabitethernet 1/0 session

My result :

R2921-8CPITR-1(config)#int gi 1/1

R2921-8CPITR-1(config-if)#ip address 2.2.2.2 255.255.255.192

% IP addresses may not be configured on L2 links.

R2921-8CPITR-1(config-if)

R2921-8CPITR-1(config)#interface gigabitEthernet 1/1.1 ?

% Unrecognized command

R2921-8CPITR-1(config)#interface gigabitEthernet 1/1 ?

<cr>

R2921-8CPITR-1(config)#

the session is not possible also ?

R2921-8CPITR-1#service-module gigabitEthernet 1/1 sess

^

% Invalid input detected at '^' marker.

R2921-8CPITR-1#

The routeur said that it's not a L3 port, so how to configure it to allow communication between the 2921 and the card ?

Is there a bug with that version I'm in 15.1(4)M4 ????

R2921-8CPITR-1#sh ver

Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Tue 20-Mar-12 18:57 by prod_rel_team

ROM: System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)

R2921-8CPITR-1 uptime is 19 hours, 21 minutes

System returned to ROM by power-on

System restarted at 16:00:45 GAB Fri Sep 14 2012

System image file is "flash0:c2900-universalk9-mz.SPA.151-4.M4.bin"

Last reload type: Normal Reload

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco CISCO2921/K9 (revision 1.0) with 479232K/45056K bytes of memory.

Processor board ID FGL1618119E

6 Gigabit Ethernet interfaces

2 terminal lines

DRAM configuration is 64 bits wide with parity enabled.

255K bytes of non-volatile configuration memory.

250880K bytes of ATA System CompactFlash 0 (Read/Write)

License Info:

License UDI:

-------------------------------------------------

Device# PID SN

-------------------------------------------------

*0 CISCO2921/K9 FGL1618119E

Technology Package License Information for Module:'c2900'

-----------------------------------------------------------------

Technology Technology-package Technology-package

Current Type Next reboot

------------------------------------------------------------------

ipbase ipbasek9 Permanent ipbasek9

security None None None

uc None None None

data None None None

Configuration register is 0x2102

R2921-8CPITR-1#

Reza Sharifi · ‎09-15-2012

Hi,

What is the output of "sh ip int bri" on the router?

Is interface gi1/0 in up and up mode?

mazamora · ‎04-10-2014

Same issue here.

I just waited a few minutes and the interface went down and back up, this time it was a L3 interface.

My guess is that it was booting the switch module IOS, and it detected it until it was fully booted:

Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet1/0, changed state to up
Apr 11 05:26:52.795: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/2, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to up
Apr 11 05:27:46.895: %LINK-5-CHANGED: Interface Embedded-Service-Engine0/0, changed state to administratively down
Apr 11 05:27:46.895: %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to administratively down
Apr 11 05:27:46.947: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to administratively down
Apr 11 05:27:47.031: %LINK-5-CHANGED: Interface GigabitEthernet0/2, changed state to administratively down
Apr 11 05:27:47.083: %LINK-5-CHANGED: Interface GigabitEthernet1/0, changed state to administratively down
Apr 11 05:27:47.895: %LINEPROTO-5-UPDOWN: Line protocol on Interface Embedded-Service-Engine0/0, changed state to down
Apr 11 05:27:48.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to down
Apr 11 05:27:49.283: %IP-5-WEBINST_KILL: Terminating DNS process
Apr 11 05:27:52.499: %LINK-3-UPDOWN: Interface GigabitEthernet1/1, changed state to up
Apr 11 05:27:53.087: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2951 Software (C2951-UNIVERSALK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 04-Sep-12 16:50 by prod_rel_team
Apr 11 05:27:53.255: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
Apr 11 05:27:53.499: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to up
Apr 11 05:28:21.435: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
Apr 11 05:29:22.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to down
Apr 11 05:29:22.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
Router>en
Router#sh ip int brief
Interface IP-Address OK? Method Status Protocol
Embedded-Service-Engine0/0 unassigned YES unset administratively down down
GigabitEthernet0/0 unassigned YES unset administratively down down
GigabitEthernet0/1 unassigned YES unset administratively down down
GigabitEthernet0/2 unassigned YES unset administratively down down
GigabitEthernet1/0 unassigned YES unset administratively down down
GigabitEthernet1/1 unassigned YES unset up down
Vlan1 unassigned YES unset down down
Router#
Apr 11 05:29:46.106: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to upconf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int g1/0
Router(config-if)#ip add 1.1.1.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#
Apr 11 05:30:09.046: %LINK-3-UPDOWN: Interface GigabitEthernet1/0, changed state to up
Apr 11 05:30:10.046: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to up
Router(config-if)#end

Manuspillai01 · ‎09-24-2013

Hi ,

try the below config..i think it should work as i have tried it in my new cisco2921 router and SM-ES3-16-P card installed in the SM slot

router(config)#interface GigabitEthernet1/0

description -CONNECTION FROM ROUTER TO SM CARD-

ip address 192.168.0.1 255.255.255.252

#end

router#service-module gigabitethernet 1/0 session

it will show trying to connect..enter once to get into the SM card config terminal as shown below

switch>en

switch#config t

switch(config)#int gigabitethernet 1/0/18

ip add 192.168.0.2 255.255.255.252

no shut