Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Hello guys, I have a L3 port-channel between 2 gigabit ethernet interfaces (one per switch Catalyst 6509), towards two giga interfaces in another two Catalyst 6509 in the other end. The port-channel is configured as follows in one of the ends (the fi...
Resolved! VSS supported in SUP 8
Hi all, I was viewing VSS configuration in latest 4500 switch configuration guidehttp://www.cisco.com/en/US/docs/switches/lan/catalyst4500/XE3.5.0E/15.21E/configuration/guide/vss.html#wp1053927Under pre requisite, it says that SUP 7E and 7LE are supp...
we are using Cisco CISCO1921/K9 (revision 1.0) with 2 Gigabit Ethernet interfaces, we want to expand the LAN connectivity, can i add Gigabyte module to the existing.? Thanks in Advance.
I'm having a problem with speed/duplex settings with the Nexus 1000v. I recently upgraded the VSM and VEMs to version 4.2(1)SV2(2.1a) with the VMware hosts on ESXi 5.1. We're now trying to bring an ESXi 5.5 host into the Nexus 1000v and when migrat...
Dear Team, We have connected ASR 1004 to Catalyst 6500 switch.The interface connected to ASR is coming up and ASR is seen in CDP neighbor of switch but we are unable to ping the ASR.In ASR we were unable to even see Catalyst 6500 in CDP neighbor det...
Resolved! vlan depend on user account
i`m asking, is possible to assign the vlan depend on user account i have a lot of sub nets and i need to link between user account and vlan,the current solution is to divide the vlan on switches
Greetings everyone, I just started at a new company in which the previous network engineer left half way through completing a new core infrastructure design. I'm kind of working off his base but made some changes. My question is, ultilizing the fol...
Resolved! Query on BGP route distribution
Hello EveryoneIn the below scenario (GNS3), IBGP peering enabled between R1-R2, R1-R3, R2-R3 and EBGP peering enabled between R2-R4,R3-R5,R4-R6,R5-R7. OSPF enabled as IGP. Scenario attached for reference. The problem I've observed in R1 is not gettin...
Resolved! how to - access list for subnet range
I have been trying to get the syntax right to allow certain outbound traffic based on subnets. the first two lines are fine but I can't get the third and fourth line to take. What is the correct way to do this?ip access-list extended TEST permit ip ...
Resolved! WAN Edge router Suggestion required
Hi,My current WAN Capacity is 300 Meg and we are currently using 3845 router, it remains 85 % in production hours with WAN utilization of 160+ Meg.I need suggestion, should i go for Cisco 3945E ( with approx 400 Meg WAN capacity as per Cisco ) or Cis...
Hi,I want to purchase Cisco ASR 1001 router, I need to run ssh , Crypto , IPSec VPN ( 3DES, ESP ) and Gre Tunnels on it.i am confused with different IOS / Licenses of ASR 1001, can any one please suggest me with the part numbers that i need to put in...
for office with two building & four floors/building having 30 computers/floor . suggest access & distribut layer multiswitch & router. for connecting four floors of each building. and switch for connecting two buildings . and finally router for c...
I have a c3750G L3 switch running c3750-ipservicesk9-mz.122-53.SE2.bin image.Attached to this switch is a server with ip 10.2.158.53 (on vlan 158)The same switch has the VLAN interface for VLAN158I am extremely confident that the NIC for the server i...
is it possible to enable to VSS with 6500 chassis when only one chassis have the WISM ?
Can someone explaind about private Vlan'swhats is the difference between private vlan and normal vlan
