i really need help on this qns i dont understand what my teacher teach.. it would be very appreciated if you can ans this qns
Lab 1.3.3: Troubleshooting a Small Network
Task 1: Examine the Logical LAN Topology
The IP address block of 172.16.30.0 /23 is subnetted to meet the following requirements:
Subnet Number of Hosts
Subnet A 174
Subnet B 60
Additional requirements and specifications:
The 0 subnet is used.
The smallest possible number of subnets that satisfy the requirements for hosts should be used,
keeping the largest possible block in reserve for future use.
Assign the first usable subnet to Subnet A.
Host computers use the first IP address in the subnet. The network router uses the last network
Based on these requirements, the following topology has been provided to you:
IP mask (decimal) 255.255.255.0
IP address 172.16.30.0
First IP host address 172.16.30.1
Last IP host address 172.16.30.254
IP mask (decimal) 255.255.255.128
IP address 172.16.31.0
First IP host address 172.16.31.1
Last IP host address 172.16.31.126
Examine each of the values in the tables above and verify that this topology meets all requirements and
specifications. Are any of the given values incorrect? ___________
If yes, correct the values in the table above and write the corrected values below:
Create a configuration table similar to the one below using your corrected values:
Device IP address Mask Gateway
Host1 172.16.30.1 255.255.255.0 172.16.30.254
Router1–Fa0/0 172.16.30.254 255.255.255.0 N/A
Host2 172.16.31.1 255.255.255.128 172.16.31.126
Router1–Fa0/1 172.16.31.126 255.255.255.128 N/A
Task 2: Cable, Erase, and Reload the Routers
Step 1: Cable the network.
Cable a network that is similar to the one in the topology diagram.
Step 2: Clear the configuration on each router.
Clear the configuration on the router using the erase startup-config command and then reload the
router. Answer no if asked to save changes.
Task 3: Configure the Host Computers
Step 1: Configure host computers.
Configure the static IP address, subnet mask, and gateway for each host computer based on the
configuration table created in Task 1. After configuring each host computer, display and verify the host
network settings with the ipconfig /all command.
Task 4: Load the Router with the Supplied Scripts
enable secret class
no ip domain-lookup
description connection to host1
ip address 172.16.30.1 255.255.255.0
description connection to switch1
ip address 220.127.116.11 255.255.255.192
line con 0
line vty 0
line vty 1 4
Task 5: Identify Connectivity Problems
Step 1: Use the ping command to test network connectivity.
Use the following table to test the connectivity of each network device
From To IP Address Ping Results
Host1 NIC IP address 172.16.30.1
Host1 Router1, Fa0/0 172.16.30.254
Host1 Router1, Fa0/1 172.16.31.126
Host1 Host2 172.16.31.1
Host2 NIC IP address 172.16.30.1
Host2 Router1, Fa0/1 172.16.31.126
Host2 Router1, Fa0/0 172.16.30.254
Host2 Host1 172.16.30.1
Task 6: Troubleshoot Network Connections
Step 1: Begin troubleshooting at the host connected to the BRANCH router.
From host PC1, is it possible to ping PC2? _________
From host PC1, is it possible to ping the router fa0/1 interface? _________
From host PC1, is it possible to ping the default gateway? _________
From host PC1, is it possible to ping itself? _________
Where is the most logical place to begin troubleshooting the PC1 connection problems?
Step 2: Examine the router to find possible configuration errors.
Begin by viewing the summary of status information for each interface on the router.
Are there any problems with the status of the interfaces?
If there are problems with the status of the interfaces, record any commands that are necessary to correct
the configuration errors.
Step 3: Use the necessary commands to correct the router configuration.
Step 4: View a summary of the status information.
If any changes were made to the configuration in the previous step, view the summary of the status
information for the router interfaces.
Does the information in the interface status summary indicate any configuration errors on Router1?
If the answer is yes, troubleshoot the interface status of the interfaces.
Has connectivity been restored? ________
Step 5: Verify the logical configuration.
Examine the full status of Fa 0/0 and 0/1. Is the IP addresses and subnet mask information in the
interface status consistent with the configuration table? _______
If there are differences between the configuration table and the router interface configuration, record any
commands that are necessary to correct the router configuration.
Why is it useful for a host to ping its own address?
Task 7: Clean Up
Unless directed otherwise by your instructor, erase the configurations and reload the switches.
Disconnect and store the cabling. For PC hosts that are normally connected to other networks (such as
the school LAN or to the Internet), reconnect the appropriate cabling and restore the TCP/IP settings.
Here is the answer of your question:
Here i am attaching the whole test scenrion of this:
and config of router.
check the both ip of router interface and mask and correct it.
Please mark this question as answered and rate it.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: