Hi,
I have upgraded from s72033-adventerprisek9_wan-mz.122-33.SXH3a.bin to s72033-advipservicesk9_wan-mz.122-33.SXI7.bin.
the problem is:
1) when i do sh bootvar after reload then i se,
BOOT variable = sup-bootdisk:sup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXH3a.bin,1; ----> OLD IMAGE
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
2) when i do sh version after reload then i see,
System image file is "sup-bootdisk:s72033-advipservicesk9_wan-mz.122-33.SXI7.bin" ----> NEW IMAGE
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
3) when i do power off and on then it goes to rommon mode
and then i have to configure: boot bootdisk:sup-bootdisk:s72033-advipservicesk9_wan-mz.122-33.SXI7.bin
but the situation is same. it shows old image in bootvar and new image in show version. output is below.
------------------------------------------------------------------------------------------------------------------------
again i configured boot system flash as below.
after saving configuration the show bootvar is,
BOOT variable = sup-bootdisk:s72033-advipservicesk9_wan-mz.122-33.SXI7.bin,1;sup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXH3a.bin,1;
CONFIG_FILE variable =
BOOTLDR variable =
Configuration register is 0x2102
Standby not ready to show bootvar
then i reloaded and what the image in bootvar is only old image, and in show version is with new image.
i do not know what is happening.
boot config:-----
boot system flash sup-bootdisk:s72033-advipservicesk9_wan-mz.122-33.SXI7.bin ------> NEW IMAGE
boot system flash sup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXH3a.bin -----> OLD IMAGE
Supervisor Engine 720 (Active) WS-SUP720-3B
sup HW type------------ 5.6 8.5(2) 12.2(33)SXI7 Ok
output:
+++++++++++++++++++++++++++++
B3ECID1-S5#sh bootv
BOOT variable = sup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXH3a.bin,1;
CONFIG_FILE variable =
BOOTLDR variable =
Configuration register is 0x2102
Standby not ready to show bootvar
B3ECID1-S5#sh ver
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI7, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Mon 18-Jul-11 05:49 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)S4, RELEASE SOFTWARE (fc1)
B3ECID1-S5 uptime is 5 minutes
Uptime for this control processor is 6 minutes
Time since B3ECID1-S5 switched to active is 5 minutes
System returned to ROM by power cycle at 08:56:43 CET Sun Jul 8 2012 (SP by power on)
System restarted at 09:29:27 CET Sun Jul 8 2012
System image file is "sup-bootdisk:s72033-advipservicesk9_wan-mz.122-33.SXI7.bin"
Last reload reason: bus error at PC 0x425F4270, address 0x0
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
--More-- third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco WS-C6509-E (R7000) processor (revision 1.4) with 458720K/65536K bytes of memory.
Processor board ID SMG1213N0B5
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from s/w reset
2 Virtual Ethernet interfaces
56 Gigabit Ethernet interfaces
8 Ten Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.
--More-- 65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
PLEASE ADVICE ME
thanks,
Shain Bharati
