01-18-2012 01:05 PM - edited 03-07-2019 04:25 AM
Please see the attached diagram to explain the network.
I'm trying to do a "port-to-port" layer 2 connection on an ASR that will bi-directionally bridge a physical interface to a sub-interface.
I tried using " connect VLAN200 Gig0/1/0 Gig0/0/3.200 interworking ethernet " but I'm not getting traffic through the connection.
Has anyone gotten this to work? If so, how? I don't think BDI will work because it requires a Layer 3 point. I have to make this Layer 2 switching.
Thanks!
Ven
01-24-2012 11:43 AM
In case anyone else runs across a need for this, I figured out a solution.
EVC is the new bridging for the ASR platform.
Configuration is simple enough:
Interface g0/0/1
description first EVC interface
no ip address
service interface 100 ethernet
encapsulation dot1q 100
bridge-domain 100
no shut
!
interface g0/0/3
description first EVC interface
no ip address
service interface 100 ethernet
encapsulation dot1q 100
bridge-domain 100
no shut
!
end
This essentially bridges the two physical interfaces together (bi-directionally) so all ethernet traffic with a dot1q tag of 100 will bridge across the router.
No un-tagged traffic will bridge.
Here's the link:
http://www.cisco.com/en/US/docs/ios-xml/ios/cether/configuration/xe-3s/ce-ether-vc-infra-xe.html
Ven
This also allows you to configure multiple service instances per physical interface, so it's scalable.
02-13-2012 06:36 AM
Hi Ven,
do you have working config for multiple service instances per interface (like switchport trunk on a switch)?
Local switching works for me when I use one interface per Vlan, single service instance per interface on ASR.
Unable to make it working when I try to add second service instance on interface and make it switchport trunk on the connected switch (N7K).
The config is below, when "service instance 23 ethernet" sits on another phy interface it works.
Once i add it to this interface as second instance, it doesn't work (another int is shut).
Switch sees ASR via cdp, but ASR doesn't see the switch in this case.
interface GigabitEthernet0/1/2
no ip address
negotiation auto
cdp enable
service instance 21 ethernet
encapsulation dot1q 21
! rewrite ingress tag translate 1-to-1 dot1q 21 symmetric
bridge-domain 21
!
service instance 23 ethernet
encapsulation dot1q 23
bridge-domain 23
interface BDI21
ip address 192.168.253.209 255.255.255.240
ip nat inside
ip policy route-map PBR-GOOGLE
cdp enable
!
interface BDI23
ip address 10.1.1.1 255.255.255.0
cdp enable
!
Thank you
Alexander Gesse
02-21-2012 06:15 AM
Alexander:
I may be mistaken, but I don't think it will work like that for you.
I couldn't get the ASRs to do BDI's like that. This is the "old-school" method of doing BDI.
In it's simplest form, the ASR will "bridge" or "locally switch" when two physical interfaces are identified with the same service instance. Put simply, if two physical interfaces are configured with the same service interface and bridge-domain ID, packets with the proper vlan tag coming into one interface will locally switch out of the other interface.
Can you provide a quickie diagram of what you're trying to accomplish?
Ven
02-21-2012 07:24 AM
Hi Ven
thank you for taking time. I actually figured out where i was mistaken and was going to update my post so someone may benefit later. The key is to have appropriate "encapsulation" statement on BDI interface as well, matching the bridge-domain and encap numbers in Service Instance part.
I am basically doing a router on stick, having N7K as a switch with trunk going to ASR as a router on stick and doing inter-vlan routing. The BDI interfaces are serving as Interface-Vlan interfaces here. It works.
Thank you
Alexander
02-29-2012 11:31 AM
Can you show me your config so I can see what you changed? I'd like to have this info too.
Ven
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide