cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2099
Views
0
Helpful
2
Replies

lost carrier error/ no neighbor

Brromeo
Level 1
Level 1

Recently replaced a 3845 in my Data Center with a ISR 4331. Used the same Fiber SFP that was in the 3845 in the 4331. 

My network monitor is showing my WAN interface and completely down. 

 

This is the output from the sh interface:

DALLAS-4331#sh int g0/0/0
GigabitEthernet0/0/0 is up, line protocol is up
Hardware is ISR4331-3x1GE, address is d0ec.35e5.xxxx (bia d0ec.35e5.xxxx)
Description: <== Connection to CenturyLink MPLS  ==>
Internet address is xx.xx.182.102/30
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not supported
Full Duplex, 1000Mbps, link type is force-up, media type is LX
output flow-control is on, input flow-control is on
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:11, output hang never
Last clearing of "show interface" counters never
Input queue: 0/375/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: Class-based queueing
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
4532 packets output, 500098 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
6938 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out

 

Insights as to where the issue lies? also the significance of the lost carrier packets. 

The WAN interface was working properly on the 3845. 

Even though the router is unavailable via WAN I am able to get to it via a secondary inter route. 

 

 

 

2 Replies 2

Reza Sharifi
Hall of Fame
Hall of Fame
Hi, Can you post "sh run" from the ISR router? Are you able to ping the provider router? HTH

I am unable to ping the provider. 

DALLAS-4331#sh run

Building configuration...

 

 

Current configuration : 22225 bytes

!

! Last configuration change at 10:29:41 CDT Wed Oct 16 2019 by admin

!

version 16.6

no service pad

service tcp-keepalives-in

service tcp-keepalives-out

service timestamps debug datetime msec localtime show-timezone

service timestamps log datetime msec localtime show-timezone

service password-encryption

service linenumber

service sequence-numbers

service unsupported-transceiver

platform qfp utilization monitor load 80

no platform punt-keepalive disable-kernel-core

!

hostname DALLAS-4331

!

boot-start-marker

boot-end-marker

!

!

vrf definition Mgmt-intf

 !

 address-family ipv4

 exit-address-family

 !

 address-family ipv6

 exit-address-family

!

card type t1 0 2

security authentication failure rate 3 log

security passwords min-length 6

logging buffered 100000

!

no aaa new-model

clock timezone CST -6 0

clock summer-time CDT recurring

no ip subnet-zero

no ip source-route

!

no ip bootp server

no ip domain lookup

ip domain name XXXX.com

ip dhcp-server 10.1.2.28

ip dhcp-server 10.2.2.28

!

!

!

!

!

!

!

!

!

!

subscriber templating

!

!

!

!

!

!

!

multilink bundle-name authenticated

!

!

!

!

isdn switch-type primary-ni

!

!

trunk group LOCAL-PRI-PSTN

 description ** LOCAL PRI Trunk Group for  PSTN **

 hunt-scheme sequential

 translation-profile incoming DID-Inbound-7to+E164

!

!

!

!

voice service voip

 mode border-element

 allow-connections h323 to h323

 allow-connections h323 to sip

 allow-connections sip to h323

 allow-connections sip to sip

 no supplementary-service sip moved-temporarily

 fax protocol t38 version 0 ls-redundancy 2 hs-redundancy 2 fallback pass-through g711ulaw

 modem passthrough nse codec g711ulaw

 sip

  bind control source-interface Loopback0

  bind media source-interface Loopback0

  registrar server

  asserted-id pai

  early-offer forced

  midcall-signaling passthru

  privacy-policy passthru

!

voice class codec 1

 codec preference 1 g711ulaw

!

voice class h323 1

  h225 timeout tcp establish 3

!

!

!

voice class e164-pattern-map 1

 description ** DAL  E164 Pattern Map for Incoming DIDs **

  e164 +1214283....$

 !

!

voice class e164-pattern-map 2

 description ** DAL Friendly Dial in SRST mode **

  e164 283....$

 !

!

voice class server-group 1

 ipv4 10.1.150.31 preference 1

 ipv4 10.2.150.31 preference 2

 description XXXX CUCM Cluster

!

!

!

voice register global

 mode esrst

 no allow-hash-in-dn

 system message XXXX DAL Fallback Mode

 max-dn 100

 max-pool 100

!

voice register pool  1

 id network 10.2.200.195 mask 255.255.255.0

 voice-class codec 1

!

!

voice translation-rule 1

 rule 1 /^2835\(...\)/ /+12142835\1/

!

!

voice translation-profile DID-Inbound-7to+E164

 translate called 1

!

!

!

!

!

voice-card 0/2

 dsp services dspfarm

 no watchdog

!

voice-card 0/4

 dsp services dspfarm

 no watchdog

!

cts logging verbose

license udi pid ISR4331/K9 sn FDO23030XM9

diagnostic bootup level minimal

spanning-tree extend system-id

!

!

!

username admin privilege 15 secret 5 $1$KfnL$HnZoBEPgRIMv9WCYES1Wu/

username tech secret 5 $1$MBgX$W80y/U1s2Ugyc4XgiTIAu.

!

redundancy

 mode none

!

!

!

!

controller T1 0/2/0

 threshold sd-ber 6

 threshold sf-ber 3

 framing esf

 clock source line primary

 linecode b8zs

 cablelength long 0db

 pri-group timeslots 1-24

 trunk-group LOCAL-PRI-PSTN timeslots 1-24 preference 1

 description PRI Inbound

!

controller T1 0/2/1

 threshold sd-ber 6

 threshold sf-ber 3

 shutdown

 framing esf

 clock source line secondary

 linecode b8zs

 cablelength long 0db

 ds0-group 1 timeslots 1-24 type e&m-wink-start dtmf dnis

!

controller T1 0/2/2

 threshold sd-ber 6

 threshold sf-ber 3

 framing esf

 linecode b8zs

 cablelength long 0db

 ds0-group 1 timeslots 1-24 type e&m-wink-start dtmf dnis

 description PRI Inbound

!

controller T1 0/2/3

 threshold sd-ber 6

 threshold sf-ber 3

 framing esf

 linecode b8zs

 cablelength long 0db

!

!

!

!

class-map match-any VOIP

 match ip dscp ef

 match ip dscp cs3

class-map match-any SAP

 match access-group name SAP

class-map match-any Video

 match ip dscp af41

 match ip dscp ef

 match ip dscp cs3

 match ip dscp cs4

 match access-group name VIDEO

!

policy-map XXXX-QoS

 class VOIP

  priority percent 40

  set ip dscp ef

 class Video

  bandwidth percent 20

  set ip dscp cs7

 class SAP

  bandwidth percent 20

  set ip dscp cs2

 class class-default

  fair-queue

policy-map XXXX-SHAPE

 class class-default

  shape average percent 90

   service-policy XXXX-QoS

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

interface Loopback0

 ip address 10.2.200.195 255.255.255.255

 no ip redirects

 no ip unreachables

 no ip proxy-arp

!

interface Loopback10

 description temp for Windstream testing

 ip address 10.2.255.2 255.255.255.255

!

interface GigabitEthernet0/0/0

 description <== Connection to CenturyLink MPLS (ETH100-16834484) ==>

 ip address xx.xx.182.102 255.255.255.252

 no ip redirects

 no ip unreachables

 no ip proxy-arp

 media-type sfp

 no negotiation auto

 service-policy output XXXX-QoS

!

interface GigabitEthernet0/0/1

 description <== Connection to DALLAS-6500-01_F1/1 ==>

 bandwidth 50000

 ip address 10.2.200.2 255.255.255.252

 no ip redirects

 no ip unreachables

 no ip proxy-arp

 ip policy route-map killme

 ip ospf message-digest-key 1 md5 7 0107141D521F

 negotiation auto

!

interface GigabitEthernet0/0/2

 description <== Connection to DALLAS-6500-02_F1/1 ==>

 bandwidth 50000

 no ip address

 no ip redirects

 no ip unreachables

 no ip proxy-arp

 ip policy route-map killme

 ip ospf message-digest-key 1 md5 7 0107141D521F

 negotiation auto

!

interface GigabitEthernet0/1/0

 bandwidth 50000

 ip address 10.2.200.6 255.255.255.252

 no ip redirects

 no ip unreachables

 no ip proxy-arp

 ip policy route-map killme

 ip ospf message-digest-key 1 md5 7 0107141D521F

 negotiation auto

!

interface GigabitEthernet0/1/1

 no ip address

 shutdown

 negotiation auto

!

interface Service-Engine0/2/0

!

interface Serial0/2/0:23

 description ** D-Channel for Controller T1

 no ip address

 encapsulation hdlc

 no cdp enable

 isdn switch-type primary-ni

 isdn incoming-voice voice

!

interface Service-Engine0/4/0

!

interface GigabitEthernet0

 vrf forwarding Mgmt-intf

 no ip address

 shutdown

 negotiation auto

!

router ospf 100

 router-id 10.2.200.195

 area 0 authentication message-digest

 summary-address 10.2.0.0 255.255.0.0

 summary-address 10.1.0.0 255.255.0.0

 redistribute bgp 65000 metric-type 1 subnets route-map BGP->OSPF

 network 10.2.0.0 0.0.0.3 area 0

 network 10.2.0.194 0.0.0.0 area 0

 network 10.2.200.0 0.0.0.3 area 0

 network 10.2.200.4 0.0.0.3 area 0

 network 10.2.200.195 0.0.0.0 area 0

 network 10.2.255.2 0.0.0.0 area 0

 network 172.22.0.204 0.0.0.3 area 0

!

router bgp 65000

 bgp log-neighbor-changes

 network 10.2.255.2 mask 255.255.255.255

 network xx.xx.182.100 mask 255.255.255.252

 aggregate-address 10.2.0.0 255.255.0.0 summary-only

 aggregate-address 10.1.0.0 255.255.0.0 summary-only

 redistribute ospf 100 route-map OSPF->BGP

 neighbor xx.xx.182.101 remote-as 209

 neighbor xx.xx.182.101 description CenturyLink MPLS

 neighbor xx.xx.182.101 default-originate

 neighbor xx.xx.182.101 soft-reconfiguration inbound

 neighbor xx.xx.182.101 route-map MPLS->BGP in

 neighbor xx.xx.182.101 route-map BGP->MPLS out

 default-metric 100

!

ip forward-protocol nd

ip http server

ip http authentication local

ip http secure-server

ip http timeout-policy idle 5 life 86400 requests 10000

ip tftp source-interface GigabitEthernet0

ip route 10.90.0.0 255.255.0.0 10.2.0.62

!

ip as-path access-list 100 permit ^$

ip ssh time-out 60

ip ssh authentication-retries 2

!

!

!

!

route-map CL_Default_MED deny 5

 match ip address prefix-list TelePacific-prefixes

!

route-map CL_Default_MED permit 10

 set metric 100

!

route-map killme permit 10

 match ip address 1

 set ip df 0

!

route-map Into_BGP permit 10

 match ip address Into_BGP

!

route-map BGP->MPLS permit 50

 match ip address prefix-list DEFAULT

 set as-path prepend 65000 65000

!

route-map BGP->MPLS permit 110

 match ip address prefix-list HOUSTON_SUM

 set as-path prepend 65000 65000

!

route-map BGP->MPLS permit 210

 match ip address prefix-list DALLAS_SUM

!

route-map BGP->MPLS permit 1000

 match as-path 100

!

route-map MPLS->BGP deny 50

 match ip address prefix-list DEFAULT

!

route-map MPLS->BGP permit 100

!

route-map CL-AS-Prepend permit 10

 set as-path prepend 65000 65000 65000

!

route-map OSPF->BGP permit 100

 match tag 100

!

route-map OSPF->BGP permit 200

 match tag 200

!

route-map OSPF->BGP permit 300

 match ip address prefix-list HOUSTON_ALL

!

route-map OSPF->BGP permit 400

 match ip address prefix-list DALLAS_ALL

!

route-map BGP->OSPF permit 100

!

route-map Prepend_for_Defualt permit 10

 match ip address Default_Only

 set as-path prepend 65000 65000

!

route-map Prepend_for_Defualt permit 20

!

route-map Into_OSPF permit 10

 match ip address Into_OSPF

!

snmp-server community XXXX RO

snmp-server location DALLAS, DATACENTER

snmp ifmib ifindex persist

!

!

control-plane

!

line con 0

 exec-timeout 5 0

 login local

 transport preferred none

 transport input none

 stopbits 1

line aux 0

 stopbits 1

line vty 0 4

 exec-timeout 5 0

 logging synchronous

 login local

 transport input ssh

line vty 5 15

 exec-timeout 5 0

 logging synchronous

 login local

 transport input ssh

!

network-clock synchronization automatic

network-clock input-source 1 controller T1 0/2/0

network-clock input-source 2 controller T1 0/2/1

ntp server 216.154.192.248 prefer

ntp server 10.1.0.33

ntp server 216.154.192.249

wsma agent exec

!

wsma agent config

!

wsma agent filesys

!

wsma agent notify

!

!

end

 

DALLAS-4331#

Review Cisco Networking for a $25 gift card