03-16-2010 10:39 PM - edited 03-06-2019 10:10 AM
hi all,
i enable mls netflow and ip route-cache flow in c7613, sup720-3bxl.
conf t
mls netflow
int gi7/2
ip route-cache flow
above configuration, i enabled mls netflow in global mode and applied "ip route-cache flow" for supervsor720 giga-ehternet interface.
but i can understand why Pkts counter is 0 in the output of "show ip cache flow"
=========================================================================
SG1#sh ip cache flow
-------------------------------------------------------------------------------
MSFC:
IP packet size distribution (378649 total packets):
1-32 64 96 128 160 192 224 256 288 320 352 384 416 448 480
.000 .152 .344 .066 .033 .012 .073 .078 .010 .009 .010 .004 .123 .051 .000
512 544 576 1024 1536 2048 2560 3072 3584 4096 4608
.002 .006 .014 .007 .000 .000 .000 .000 .000 .000 .000
IP Flow Switching Cache, 4456704 bytes
9 active, 65527 inactive, 31491 added
688308 ager polls, 0 flow alloc failures
Active flows timeout in 30 minutes
Inactive flows timeout in 15 seconds
IP Sub Flow Cache, 270664 bytes
9 active, 16375 inactive, 31491 added, 31491 added to flow
0 alloc failures, 0 force free
1 chunk, 0 chunks added
last clearing of statistics 1d02h
Protocol Total Flows Packets Bytes Packets Active(Sec) Idle(Sec)
-------- Flows /Sec /Flow /Pkt /Sec /Flow /Flow
TCP-Telnet 6953 0.0 4 41 0.3 0.2 2.7
TCP-FTP 35 0.0 14 64 0.0 0.4 15.5
TCP-other 23823 0.2 1 47 0.2 0.0 15.5
UDP-other 627 0.0 470 217 3.0 282.0 13.5
ICMP 52 0.0 420 84 0.2 1799.0 1.5
Total: 31490 0.3 11 183 3.9 8.6 12.6
SrcIf SrcIPaddress DstIf DstIPaddress Pr SrcP DstP Pkts
Gi7/2 172.31.247.238 Local 10.2.1.1 01 0000 0800 341
Gi7/2 172.31.247.238 Local 10.2.1.1 06 C8FD 0017 3
Gi7/2 172.31.247.238 Local 1.1.1.1 06 DEAD 0017 18
Gi7/2 172.31.247.238 Local 10.2.1.1 06 E032 1011 1
Gi7/2 172.31.247.238 Local 10.2.1.1 06 E030 1011 1
Gi7/2 172.31.247.238 Local 10.2.1.1 06 E02E 1011 1
Gi7/2 172.31.247.238 Local 10.2.1.1 06 E02C 1011 1
Gi7/2 172.31.247.238 Local 10.2.1.1 11 A123 00A1 2697
Gi7/2 172.31.247.238 Local 10.2.1.1 11 A124 00A1 1380
-------------------------------------------------------------------------------
PFC:
Displaying Hardware entries in Module 7
SrcIf SrcIPaddress DstIPaddress Pr SrcP DstP Pkts
Fa10/0/0 10.1.9.1 10.4.9.41 132 4013 4013 2851
Fa3/0/0 10.1.3.1 10.4.20.11 132 4019 4019 0
Fa10/0/0 10.1.9.1 10.7.9.21 132 7011 7011 3387
Fa3/0/1 10.1.4.1 10.4.10.11 132 4009 4009 2579
Fa3/0/0 10.1.3.1 10.4.9.11 132 4009 4009 2579
Fa10/0/1 10.1.10.1 10.4.10.41 132 4014 4014 2850
Fa10/0/1 10.1.10.1 10.7.10.21 132 7011 7011 3107
Fa5/0/0 10.1.5.1 10.4.9.12 132 4010 4010 2581
Fa10/0/0 10.1.9.1 10.4.9.21 132 4011 4011 2644
Fa3/0/1 10.1.4.1 10.7.16.21 132 7019 7019 7
Fa10/0/1 10.1.10.1 10.4.10.21 132 4011 4011 2656
Fa10/0/0 10.1.9.1 10.8.1.11 132 8000 8000 21
Fa3/0/1 10.1.4.1 10.7.15.11 132 7015 7015 7
Fa10/0/1 10.1.10.1 10.7.2.11 132 7001 7001 20
Fa5/0/1 10.1.6.1 10.4.10.12 132 4010 4010 2581
Fa10/0/1 10.1.10.1 10.8.2.11 132 8000 8000 15
Fa3/0/0 10.1.3.1 10.7.16.11 132 7015 7015 7
Gi7/2 172.31.247.238 10.2.1.1 tcp 57386 4113 0
Fa3/0/1 10.1.4.1 10.7.15.21 132 7019 7019 7
Fa10/0/0 10.4.1.11 10.1.9.1 icmp 8 0 0
Fa3/0/0 10.1.3.1 10.7.16.21 132 7019 7019 7
above output consists two parts : MSFC and PFC
if i just enable ip route-cache flow for gi7/2(not enable mls netflow in global mode)
then PFC part is not shown. it shows just MSFC part
config t
no mls netflow
int gi7/2
ip route-cache flow
end
show ip cache flow
-------------------------------------------------------------------------------
MSFC:
IP packet size distribution (384674 total packets):
1-32 64 96 128 160 192 224 256 288 320 352 384 416 448 480
.000 .152 .343 .066 .033 .012 .073 .078 .010 .009 .010 .004 .123 .051 .000
512 544 576 1024 1536 2048 2560 3072 3584 4096 4608
.002 .006 .014 .007 .000 .000 .000 .000 .000 .000 .000
IP Flow Switching Cache, 4456704 bytes
8 active, 65528 inactive, 31973 added
699019 ager polls, 0 flow alloc failures
Active flows timeout in 30 minutes
Inactive flows timeout in 15 seconds
IP Sub Flow Cache, 270664 bytes
8 active, 16376 inactive, 31973 added, 31973 added to flow
0 alloc failures, 0 force free
1 chunk, 0 chunks added
last clearing of statistics 1d02h
Protocol Total Flows Packets Bytes Packets Active(Sec) Idle(Sec)
-------- Flows /Sec /Flow /Pkt /Sec /Flow /Flow
TCP-Telnet 7063 0.0 4 41 0.3 0.2 2.7
TCP-FTP 35 0.0 14 64 0.0 0.4 15.5
TCP-other 24189 0.2 1 47 0.2 0.0 15.5
UDP-other 633 0.0 474 218 3.1 285.0 13.5
ICMP 53 0.0 420 84 0.2 1799.0 1.5
Total: 31973 0.3 11 183 3.9 8.6 12.6
SrcIf SrcIPaddress DstIf DstIPaddress Pr SrcP DstP Pkts
Gi7/2 172.31.247.238 Local 10.2.1.1 01 0000 0800 261
Gi7/2 172.31.247.238 Local 1.1.1.1 06 DEAD 0017 189
Gi7/2 172.31.247.238 Local 10.2.1.1 06 E37A 1011 1
Gi7/2 172.31.247.238 Local 10.2.1.1 06 E378 1011 1
Gi7/2 172.31.247.238 Local 10.2.1.1 06 E37E 1011 1
Gi7/2 172.31.247.238 Local 10.2.1.1 06 E37C 1011 1
Gi7/2 172.31.247.238 Local 10.2.1.1 11 A123 00A1 2190
Gi7/2 172.31.247.238 Local 10.2.1.1 11 A124 00A1 1035
-------------------------------------------------------------------------------
PFC:
Displaying Hardware entries in Module 7
SrcIf SrcIPaddress DstIPaddress Pr SrcP DstP Pkts
Displaying Hardware entries in Module 8
SrcIf SrcIPaddress DstIPaddress Pr SrcP DstP Pkts
above output say that "ip route-cache flow" shows the cache entry in MSFC.
in opposite,
if i just enable mls netflow(not enable ip route-cache flow for gi7/2)
then MSFC part is not shown. it shows just PFC part
conf t
int gi7/2
no ip route-cache flow
exit
mls netflow
end
SG1#sh ip cache flow
-------------------------------------------------------------------------------
MSFC:
IP packet size distribution (0 total packets):
1-32 64 96 128 160 192 224 256 288 320 352 384 416 448 480
.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000
512 544 576 1024 1536 2048 2560 3072 3584 4096 4608
.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000
IP Flow Switching Cache, 0 bytes
0 active, 0 inactive, 0 added
0 ager polls, 0 flow alloc failures
Active flows timeout in 30 minutes
Inactive flows timeout in 15 seconds
last clearing of statistics 00:00:11
Protocol Total Flows Packets Bytes Packets Active(Sec) Idle(Sec)
-------- Flows /Sec /Flow /Pkt /Sec /Flow /Flow
SrcIf SrcIPaddress DstIf DstIPaddress Pr SrcP DstP Pkts
-------------------------------------------------------------------------------
PFC:
Displaying Hardware entries in Module 7
SrcIf SrcIPaddress DstIPaddress Pr SrcP DstP Pkts
Fa10/0/0 10.1.9.1 10.4.9.41 132 4013 4013 20
Fa3/0/1 10.1.4.1 10.4.10.11 132 4009 4009 16
Fa3/0/0 10.1.3.1 10.4.9.11 132 4009 4009 16
Fa10/0/1 10.1.10.1 10.8.2.11 132 8000 8000 3
Fa10/0/1 10.1.10.1 10.7.10.21 132 7011 7011 15
Fa10/0/1 10.1.10.1 10.4.10.41 132 4014 4014 19
Fa10/0/0 10.1.9.1 10.7.9.21 132 7011 7011 15
Fa5/0/0 10.1.5.1 10.4.9.12 132 4010 4010 15
Fa10/0/0 10.1.9.1 10.4.9.21 132 4011 4011 15
Fa3/0/1 10.1.4.1 10.7.16.21 132 7019 7019 2
Fa10/0/1 10.1.10.1 10.4.10.21 132 4011 4011 15
Fa10/0/1 10.1.10.1 10.4.2.11 132 4001 4001 2
Fa5/1/1 10.1.8.1 100.1.8.13 132 2000 2000 1
Gi7/2 172.31.247.238 10.2.1.1 tcp 58729 4113 0
Fa3/0/0 10.1.3.1 10.7.15.21 132 7019 7019 5
Gi7/2 172.31.247.238 10.2.1.1 icmp 8 0 0
Fa10/0/0 10.7.1.11 10.1.9.1 icmp 8 0 0
Fa10/1/1 10.1.12.1 10.7.52.11 132 17001 17001 1
Fa10/0/0 10.1.9.1 10.8.1.11 132 8000 8000 2
Fa3/0/1 10.1.4.1 10.4.9.31 132 4007 4007 1
Fa10/1/1 10.7.52.11 10.1.12.1 icmp 4 0 0
Fa10/1/0 10.1.11.1 10.7.51.11 132 17001 17001 4
Fa10/0/1 10.7.2.11 10.1.10.1 icmp 8 0 0
above output,
i can understand why Pkts count is 0.
i think Pkts count = 0 means no packet
but why 0 count is shown?
the packets are cpu punted packets?
so counter is 0?
if i'm right, the entries(that has count=0) are punted RP cpu.
am i right?
is there anyone about this?
relative url :
03-17-2010 06:14 AM
Hello Sanghee,
when you enable MLS netflow traffic is processed by PFC so counters for MSFC are 0
you shouldn't look at MSFC statistics at this point.
it says :
>>
The NetFlow feature on the RP captures statistics for flows routed in software.
For additional information about configuring NetFlow on the RP, see the Cisco IOS NetFlow Configuration Guide, Release 12.2SX.
Hope to help
Giuseppe
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide