12-07-2014 12:42 PM - edited 03-07-2019 09:48 PM
Hello, I have router 5 and router 7 as OSPF neighbours connected via area 24.
Router 5 is running EIGRP and OSPF. Router 7 is only running OSPF. I am trying to redistribute the OSPF route 172.16.100.0/25 from router 7 into router 5's EIGRP instance.
However, I cannot seem to redistribute that network into Router 5.
Can someone please take a quick look at the configs below. I am sure it is something simple.
Thank you kindly for any help.
******************************************************
ROUTER 5 (EIGRP and OSPF)
*****************************************************
ip cef
no ipv6 cef
!
!
!
!
license udi pid CISCO2911/K9 sn FTX1524HT0O
!
spanning-tree mode pvst
!
interface GigabitEthernet0/0
ip address 192.168.3.1 255.255.255.0
duplex auto
speed auto
!
interface GigabitEthernet0/1
ip address 192.168.1.1 255.255.255.0
duplex auto
speed auto
!
interface GigabitEthernet0/2
ip address 192.168.2.1 255.255.255.0
duplex auto
speed auto
!
interface Vlan1
no ip address
shutdown
!
router eigrp 100
redistribute ospf 1 metric 1000000 10 255 1 1500
network 192.168.2.0
network 192.168.1.0
auto-summary
!
router ospf 1
log-adjacency-changes
redistribute eigrp 100 metric-type 1 subnets
network 192.168.3.0 0.0.0.255 area 24
!
ip classless
!
ip flow-export version 9
!
line con 0
!
line aux 0
!
line vty 0 4
login
!
!
!
end
************************************************************************************************************
ROUTER 7 (only OSPF)
***********************************************************************************************************
hostname Router
!
ip cef
no ipv6 cef
!
license udi pid CISCO2911/K9 sn FTX1524D5LZ
!
spanning-tree mode pvst
!
interface GigabitEthernet0/0
ip address 192.168.3.2 255.255.255.0
duplex auto
speed auto
!
interface GigabitEthernet0/1
ip address 172.16.100.1 255.255.255.0
duplex auto
speed auto
!
interface GigabitEthernet0/2
ip address 192.168.4.2 255.255.255.0
duplex auto
speed auto
!
interface Vlan1
no ip address
shutdown
!
router ospf 1
log-adjacency-changes
network 172.16.100.0 0.0.0.255 area 44
network 192.168.3.0 0.0.0.255 area 24
network 192.168.4.0 0.0.0.255 area 34
!
ip classless
!
ip flow-export version 9
!
!
line con 0
!
line aux 0
!
line vty 0 4
login
!
!
!
end
Solved! Go to Solution.
12-07-2014 01:53 PM
Are you trying to connect 2 areas together without area 0?
change "network 172.16.100.0 0.0.0.255 area 44" to network 172.16.100.0 0.0.0.255 area 24
and test again
HTH
12-07-2014 01:36 PM
Hi,
Can you post the output of "sh ip route" from both routers?
Is OSPF peering up between the 2 routers?
sh ip os nei
HTH
12-07-2014 01:39 PM
here is show ip route from router 5:
" 192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.1.0/24 is directly connected, GigabitEthernet0/1
L 192.168.1.1/32 is directly connected, GigabitEthernet0/1
192.168.2.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.2.0/24 is directly connected, GigabitEthernet0/2
L 192.168.2.1/32 is directly connected, GigabitEthernet0/2
192.168.3.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.3.0/24 is directly connected, GigabitEthernet0/0
L 192.168.3.1/32 is directly connected, GigabitEthernet0/0
D EX 192.168.4.0/24 [105/5376] via 192.168.2.2, 01:26:47, GigabitEthernet0/2"
Here is show ip route from router 7:
172.16.0.0/16 is variably subnetted, 2 subnets, 2 masks
C 172.16.100.0/24 is directly connected, GigabitEthernet0/1
L 172.16.100.1/32 is directly connected, GigabitEthernet0/1
O E1 192.168.1.0/24 [110/21] via 192.168.3.1, 01:43:21, GigabitEthernet0/0
[110/21] via 192.168.4.1, 01:41:43, GigabitEthernet0/2
O E1 192.168.2.0/24 [110/21] via 192.168.3.1, 01:43:21, GigabitEthernet0/0
[110/21] via 192.168.4.1, 01:41:43, GigabitEthernet0/2
192.168.3.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.3.0/24 is directly connected, GigabitEthernet0/0
L 192.168.3.2/32 is directly connected, GigabitEthernet0/0
192.168.4.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.4.0/24 is directly connected, GigabitEthernet0/2
L 192.168.4.2/32 is directly connected, GigabitEthernet0/2
12-07-2014 01:42 PM
Yes, neighbor relationships seem good.
show ip ospf neighbor from Router 5:
Neighbor ID Pri State Dead Time Address Interface
172.16.100.1 1 FULL/BDR 00:00:38 192.168.3.2
show ip ospf neighbor from router 7:
172.16.100.2 1 FULL/DR 00:00:35 172.16.100.2 GigabitEthernet0/1
192.168.3.1 1 FULL/DR 00:00:34 192.168.3.1 GigabitEthernet0/0
192.168.4.1 1 FULL/DR 00:00:39 192.168.4.1 GigabitEthernet0/2
12-07-2014 01:53 PM
Are you trying to connect 2 areas together without area 0?
change "network 172.16.100.0 0.0.0.255 area 44" to network 172.16.100.0 0.0.0.255 area 24
and test again
HTH
12-07-2014 04:15 PM
You are running multi-area OSPF without a backbone area (area 0), which from design point of view will not work.
The reason why on R5 routing table you see only 192.168.3.0 (area 24) prefix and not 172.16.100.0 or 192.168.4.0 is because the last two prefixes are part of OSPF area 44 and 34 (on R7), and as I said earlier by design the prefixes from area 44 and 34 will not make it to area 24 (the Point-2-Point between R7 and R5), so in this case the ABR (R7) will not be able to forward LSA type-3 (inter-area routes) to area 24.
You need to introduce a backbone area or run the same area number on all interfaces respectively on R7.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide