cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1097
Views
0
Helpful
4
Replies
Highlighted
Beginner

poe is not working on WS-X6748-SFP.

Hi All,

I am trying to connect poe device on WS-X6748-SFP port, it showing inline power not supported.

It means this module not support POE or I have to enable something...

Appreciate if any one can help on this.. Thanks!

ABCD#sh power inline gi1/4/8

Interface Gi1/4/8: inline power not supported

ABCD#show power

system power redundancy mode = redundant

system power total =     5771.64 Watts (137.42 Amps @ 42V)

system power used =      1456.98 Watts (34.69 Amps @ 42V)

system power available = 4314.66 Watts (102.73 Amps @ 42V)

                        Power-Capacity PS-Fan Output Oper

PS   Type               Watts   A @42V Status Status State

---- ------------------ ------- ------ ------ ------ -----

1    WS-CAC-6000W       5771.64 137.42 OK     OK     on

2    WS-CAC-6000W       5771.64 137.42 OK     OK     on

                        Pwr-Allocated  Oper

Fan  Type               Watts   A @42V State

---- ------------------ ------- ------ -----

1    WS-C6509-E-FAN      210.00  5.00  OK

                        Pwr-Requested  Pwr-Allocated  Admin Oper

Slot Card-Type          Watts   A @42V Watts   A @42V State State

---- ------------------ ------- ------ ------- ------ ----- -----

2    WS-SVC-FWM-1        171.78  4.09   171.78  4.09  on    on

4    WS-X6748-SFP        292.74  6.97   292.74  6.97  on    on

5    VS-S720-10G         338.10  8.05   338.10  8.05  on    on

6    WS-X6708-10GE       444.36 10.58   444.36 10.58  on    on

system auxiliary power mode = off

system auxiliary power redundancy operationally = non-redundant

system primary connector power limit =   10920.00 Watts (260.00 Amps @ 42V)

system auxiliary connector power limit = 10500.00 Watts (250.00 Amps @ 42V)

system primary power used =              1456.98 Watts (34.69 Amps @ 42V)

system auxiliary power used =            0 WattTENANT-CORE-SWITCH#show power
system power redundancy mode = redundant
system power total =     5771.64 Watts (137.42 Amps @ 42V)
system power used =      1456.98 Watts (34.69 Amps @ 42V)
system power available = 4314.66 Watts (102.73 Amps @ 42V)
                        Power-Capacity PS-Fan Output Oper
PS   Type               Watts   A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1    WS-CAC-6000W       5771.64 137.42 OK     OK     on
2    WS-CAC-6000W       5771.64 137.42 OK     OK     on
                        Pwr-Allocated  Oper
Fan  Type               Watts   A @42V State
---- ------------------ ------- ------ -----
1    WS-C6509-E-FAN      210.00  5.00  OK
                        Pwr-Requested  Pwr-Allocated  Admin Oper
Slot Card-Type          Watts   A @42V Watts   A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
2    WS-SVC-FWM-1        171.78  4.09   171.78  4.09  on    on
4    WS-X6748-SFP        292.74  6.97   292.74  6.97  on    on
5    VS-S720-10G         338.10  8.05   338.10  8.05  on    on
6    WS-X6708-10GE       444.36 10.58   444.36 10.58  on    on
system auxiliary power mode = off
system auxiliary power redundancy operationally = non-redundant
system primary connector power limit =   10920.00 Watts (260.00 Amps @ 42V)
system auxiliary connector power limit = 10500.00 Watts (250.00 Amps @ 42V)
system primary power used =              1456.98 Watts (34.69 Amps @ 42V)
system auxiliary power used =            0 Watt

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
Hall of Fame Expert

Hi,

Fiber modules (SFP) do not support POE.  Only copper modules do.

for example this card support POE:

WS-X6548-GE-45AF

Have a look at table-7 in this link:

http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps708/product_data_sheet0900aecd8017376e_ps2797_Products_Data_Sheet.html

HTH

View solution in original post

4 REPLIES 4
Highlighted
Hall of Fame Expert

Hi,

Fiber modules (SFP) do not support POE.  Only copper modules do.

for example this card support POE:

WS-X6548-GE-45AF

Have a look at table-7 in this link:

http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps708/product_data_sheet0900aecd8017376e_ps2797_Products_Data_Sheet.html

HTH

View solution in original post

Highlighted

I was trying to connect Cisco Access Point using GLCT to the port..

Thanks for your valuable information.

Highlighted

Sorry, it will not work with GLC-T.

Please rate and close the threat, so others can benefit from it.

Highlighted
Hall of Fame Community Legend

I was trying to connect Cisco Access Point using GLCT to the port..

Won't work because a GLC-T SFP module doesn't support PoE either.

The only way to get the WAP working is to either use a power injector or a power pack/power brick.

Content for Community-Ad