01-16-2014 05:32 PM - edited 03-07-2019 05:37 PM
Dear Experts,
My switch running is normal but suddenly it has problem with red light(Output fail) as attached file.
I also try reboot but seem to switch can not
There is output while switch reboot:
**********************************************************
* *
* Welcome to Rom Monitor for WS-X45-SUP6-E System. *
* Copyright (c) 2003-2009 by Cisco Systems, Inc. *
* All rights reserved. *
* *
**********************************************************
Flash die # 0: Intel 33554432Bytes
Flash die # 1: Intel 33554432Bytes
Flash die # 2: Intel 33554432Bytes
Flash die # 3: Intel 33554432Bytes
Determining FTL format status of volume.
Volume is FTL formatted.
Checking the partition table and boot sector...
Checking FAT, Files and Directories...
Reclaiming unused space...
Updating FAT...
Rom Monitor Program Version 12.2(44r)SG5
CPU Rev: 2.1, Board Rev: 6, Board Type: 10, CPLD Jawa Rev: 18
Chassis: WS-C4507R-E
Front Panel Phy is Bcm5482s
Got Mac Address: 00:25:84:1e:33:bc
MAC Address : 00-25-84-1e-33-bc
Ip Address : Not set.
Netmask : Not set.
Gateway : Not set.
TftpServer : Not set.
***** The system will autoboot in 5 seconds *****
Type control-C to prevent autobooting.
. . . . .
******** The system will autoboot now ********
config-register = 0x2101
Autobooting using the first file from bootflash.....
Rommon reg: 0x00004380
Reset2Reg: 0x00000FFF
#
Darkside controller 0x0B394EBC..0x0B3A326E original size:0x00012092#
Tatooine controller 0x0B3A326F..0x0B40C25B original size:0x00094F89##
Forerunner controller 0x0B40C25C..0x0B4D1EA8 original size:0x001D0F9C
###############
diagsk5 version 3.2_a
prod: WS-X45-SUP6-E part: 73-10597-12 serial: JAE14190WMV
Power-on-self-test for Module 3: WS-X45-SUP6-E
Test Status: (. = Pass, F = Fail, U = Untested)
CPU Subsystem Tests ...
seeprom: Pass
Traffic: L3 Looopback ...
Test Results: Pass
Traffic: L2 Loopback ...
Test Results: Pass
Switching Subsystem Memory ...
Packet Memory Test Results: Pass
Module 3 Passed
Exiting to ios...
Rommon reg: 0x00000380
#######################################################
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-IPBASE-M), Version 12.2(50)SG3, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Tue 07-Jul-09 20:28 by prod_rel_team
Image text-base: 0x10000000, data-base: 0x1222AE9C
Any help are appreciated
Thanks & Regards,
01-16-2014 06:24 PM
I am suspecting the extraction fan is running low RPM or is blocked.
Power off one of the PS (not the entire chassis), wait for 5 seconds and power it back on.
Make sure both PS do not sound like loud squeeking or squeeling sound.
01-16-2014 08:05 PM
Hello,
Thank you for feedback.
I already tried power up one of each time, but still problem.
Before this time, i did not change any on this chassis.
Regards,
01-17-2014 05:37 PM
Any one please help?
01-18-2014 11:39 AM
Hi,
See this:
Hope it helps.
12-02-2015 11:02 PM
Hello,
How did you fix this problem.?
Regards,
12-03-2015 12:14 AM
Hi,
In my case, the fans on left chassis is very dusty. I shutdown the Switch and cleaned the fans after that all status is fine.
You also should see the status of all light where is the light warning then focus that problem.
Hope this can help you.
Regards,
12-03-2015 12:24 AM
Hi,
4507R+E both PS are showing "output fail" and switch stops working. (Switch photo attached).
Powering OFF and ON both the power supplies fixes the probem for few days.
After powering off and on, PS and FAN status shows ok
This problem has repeated twice now.
=======================================================
------------------ show power detail ------------------
Power Fan Inline
Supply Model No Type Status Sensor Status
------ ---------------- --------- ----------- ------- -------
PS1 PWR-C45-4200ACV AC 4200W good good good
PS1-1 220V good
PS1-2 220V good
PS2 PWR-C45-4200ACV AC 4200W good good good
PS2-1 220V good
PS2-2 220V good
Power supplies needed by system : 1
Power supplies currently available : 2
Power Summary Maximum
(in Watts) Used Available
---------------------- ---- ---------
System Power (12V) 808 1360
Inline Power (-50V) 0 3352
Backplane Power (3.3V) 40 40
---------------------- ---- ---------
Total 848 (not to exceed Total Maximum Available = 4200)
=====================================
Regards,.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide