cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
416
Views
0
Helpful
1
Replies

qos switch 2960s problem

eddanilo2016
Level 1
Level 1

hi guys

 

I need your help I have the following configuration but the qos does not work for me

 

SW-Core(config)#ip access-list extended qos

SW-Core(config-ext-nacl)#permit ip any host 192.168.1.30

SW-Core(config-ext-nacl)#permit ip any host 192.168.210

SW-Core(config-ext-nacl)#permit ip any host 192.168.1.248

 

 

 

SW-Core(config)#class-map qos-services

SW-Core(config-cmap)#match access-group name qos

 

SW-Core(config)#policy-map politica-qos

SW-Core(config-pmap)#class qos-services

SW-Core(config-pmap-c)#set dscp af11

 

 

Here I apply the interface the policy

 

interface GigabitEthernet1/0/6
switchport access vlan 110
switchport mode access
spanning-tree portfast
service-policy input politica-qos

 

 

Here I verify that I am applying but when I make connections to those destinations it does not work for me

 

SW-Core#show policy-map interface gigabitEthernet 1/0/6
GigabitEthernet1/0/6

Service-policy input: politica-qos

Class-map: qos-services (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name qos

Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
0 packets, 0 bytes
5 minute rate 0 bps

 

thanks for your help

 

regards

 

edwin

 

 

 

 

 

 

 

 

 

1 Reply 1

eddanilo2016
Level 1
Level 1

hi guys

 

I need your help I have the following configuration but the qos does not work for me

 

SW-Core(config)#ip access-list extended qos

SW-Core(config-ext-nacl)#permit ip any host 192.168.1.30

SW-Core(config-ext-nacl)#permit ip any host 192.168.210

SW-Core(config-ext-nacl)#permit ip any host 192.168.1.248

 

 

 

SW-Core(config)#class-map qos-services

SW-Core(config-cmap)#match access-group name qos

 

SW-Core(config)#policy-map politica-qos

SW-Core(config-pmap)#class qos-services

SW-Core(config-pmap-c)#set dscp af11

 

 

Here I apply the interface the policy

 

interface GigabitEthernet1/0/6
switchport access vlan 110
switchport mode access
spanning-tree portfast
service-policy input politica-qos

 

 

Here I verify that I am applying but when I make connections to those destinations it does not work for me

 

SW-Core#show policy-map interface gigabitEthernet 1/0/6
GigabitEthernet1/0/6

Service-policy input: politica-qos

Class-map: qos-services (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name qos

Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
0 packets, 0 bytes
5 minute rate 0 bps

 

thanks for your help

 

regards

 

edwin

 

 

 

 

 

 

 

Review Cisco Networking for a $25 gift card