06-21-2010 03:00 AM - edited 03-06-2019 11:40 AM
Hi,
I am having Catalyst 2960-SI PoE24 switches with image files c2960-lanlitek9-mz.122-50.SE4.bin & c2960-lanlitek9-mz.122-50.SE3.bin
I want to configure RSPAN vlan.
I am not getting command remote span in vlan mode with any of the image.
I am only getting an option to configure interface in monitor session 1 destination command.
Can anyone help me for the same ?
Regards,
Nimit
06-21-2010 03:48 AM
Hi,
I am having Catalyst 2960-SI PoE24 switches with image files c2960-lanlitek9-mz.122-50.SE4.bin & c2960-lanlitek9-mz.122-50.SE3.bin
I want to configure RSPAN vlan.
I am not getting command remote span in vlan mode with any of the image.
I am only getting an option to configure interface in monitor session 1 destination command.
Can anyone help me for the same ?
Regards,
Nimit
Hi Nimit,
Check out the below link for step by step configuration of RSPAN on 2960 switch
Hope to help !!
Ganesh.H
Remember to rate the helpful post
06-21-2010 04:13 AM
Hi Ganesh,
Thanks for your support.
I am also referring the same document for configuration.
But switch is not accepting perticular commands like remate span in vlan mode.
only having interface option to configure in monitor session 1 destination command but not having vlan option.
is there anything required to enable RSPAN for vlan or may be ios is not supported for it ?
Regards,
Nimit
06-21-2010 04:29 AM
Hi Ganesh,
Thanks for your support.
I am also referring the same document for configuration.
But switch is not accepting perticular commands like remate span in vlan mode.
only having interface option to configure in monitor session 1 destination command but not having vlan option.
is there anything required to enable RSPAN for vlan or may be ios is not supported for it ?
Regards,
Nimit
Hi Nimit,
under vlan mode when you configure remote- ? what is the output it is showing..
Ganesh.H
06-21-2010 04:41 AM
Hi Ganesh,
I am not even getting an option to configure remote in vlan mode.
If i will create VTP on L3, create remote span vlan on it and the same will get populate to all other switches; will it work ?
This is live setup so i cant do any R&D.
Regards,
Nimit
06-21-2010 05:04 AM
Hi Ganesh,
I am not even getting an option to configure remote in vlan mode.
If i will create VTP on L3, create remote span vlan on it and the same will get populate to all other switches; will it work ?
This is live setup so i cant do any R&D.
Regards,
Nimit
Hi Nimit,
No dont do anything on live setup just make implementation plan out with backout plan and do take plan change window to do the same.
HTH
Ganesh.H
06-21-2010 05:52 AM
Hi,
One more thing to update that switch is LAN light version.
Is RSPAN supported on LAN light ?
Regards,
Nimit
06-21-2010 11:18 PM
Hi,
One more thing to update that switch is LAN light version.
Is RSPAN supported on LAN light ?
Regards,
Nimit
Hi Nimit,
Following ios c2960-lanlitek9-mz.122-50.SE3.bin and c2960-lanlitek9-mz.122-50.SE4.bin is supported for remote span as per cisco feature navigator.
Hope to Help !!
Ganesh.H
06-22-2010 03:09 AM
Hi,
Thanks for support.
As per the Cisco PPT attached it is shown that RSPAN is not supported on LAN lite.
We have also cross checked on cisco feature navigator. It shows that RSPAN supports the specified IOS. But it is only supporting for interface not for vlan.
While configuring monitor session for destination we are only getting an option to configure interface not remote SPAN.
Regards,
Nimit
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide