Hello1)what's the stack cable that connect two 3560-E togather via 10 gig?can u give me the link for it?2)can we run 10gig over copper?if so what is the module/cable for that?Thanks
Hello1)what's the stack cable that connect two 3560-E togather via 10 gig?can u give me the link for it?2)can we run 10gig over copper?if so what is the module/cable for that?Thanks
Hi AllI have 3500 series switch that is showing just two giga ports all 24 ports are not showing can any help me its IOS were old after updating IOS still it is on same postion mean showing two giga ports 1,2
Based on the Cisco documentation I added these lines into the config of the switch:policy-map jumbo class class-default mtu 9216system qos service-policy jumboWhen I run a show int though I'm still seeing the MTU set as 1500. Any ideas? Is the...
Hi,We have a switchports issue in this specific switch, wherein some switchports cannot beturned on. Whenever we try to perform a (shut/no shut) on the interface, it shows thismessage:----------------Fa0/1 can't be brought up because it failed POST ...
hi,can someone please help verify the following configuration for Cat2960version 12.2no service padservice timestamps debug datetime localtime show-timezoneservice timestamps log datetimeno service password-encryptionservice sequence-numbers!hostname...
I have not done a whole lot of access-lists before.I have Cisco 3560 switch and I need to add an access-list. Basically I have six servers that are logged into remotely:10.0.0.110.0.0.210.0.0.310.0.0.410.0.0.510.0.0.6Users are able to SSH to the ser...
I have an ISR2811 with a primary BGP learned route via ethernet and a backup BRI connection with a floating static route (admin distance of 200). The site learns routes via BGP over the primary connection when the primary connection is in place. Duri...
Hi,I've got a rack with a 7AMP limit in the UK, will the 7206VXR/NPE-G2 router work in that environment? All I've got happening with this router is eigrp running to connect an OC3 circuit.ThanksDan
Hi,I was wondering if anyone knows if broadcast packets are process-switched using the "IP Input" process by the CPU.
Hi,On my asa firewall I've got a connection where I specify a static route for the destination ip of 10.138.24.228. However, I've now setup a VPN to the same location however, the destination ip I've been given is 10.92.24.228. The problem I have is ...
HiI've a big problem with 3750 (IOS version c3750-ipservicesk9-tar.122-53.SE)Two Vlan are defined on 3750:- vlan 20 - ip 192.168.20.253- vlan 10 - ip 192.168.10.253All client on vlan 20 have as default gateway 192.168.20.253All client on vlan 10 have...
Dear all,I have a question about my 6500 CatOS, so those both 6500 Catos are used to connect all my Servers to them, those two 6500 they have redundant Link to our two core switch with layer 2 and 3 switches.My question is we have backbonefast enable...
Switches 1 and 2 are L2 and running rstp - both with vlan 10 on themswitches 3 and 4 are routed with SVIs for vlan 10 on both of them - HSRPall uplinks are dot1q 10 Gig that allow vlan 10Switch 1 is the root bridge for vlan 10.Given this, which ports...
Hi everyone,We have 2 Cisco Nexus 5020 switches and I wanted to do some rate-limiting experiments with them. But, the documentation for Nexus 5000 series switches don't mention anything regarding rate-limiting. (Nexus 7000 series switches do)My quest...
We have a web server running inside LAN with the ip 172.16.1.200 on port 80. Even after configuring NAT "ip nat inside source static tcp 172.16.1.200 80 interface Dialer0 80" on DSL Router [Cisco 1720, ip 172.16.1.100], it is not possible to access t...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-16-2024 12:15 PM | ||
10-15-2024 03:13 AM | ||
10-14-2024 02:50 AM | ||
10-09-2024 11:22 AM | ||
10-08-2024 08:34 PM |
User | Count |
---|---|
10 | |
7 | |
6 | |
6 | |
6 |