Hi all,
We have an old 3508XL switch. We are trying to connect a new 2960 to it but we purchased the incorrect SFP insert and that speed can only do 100mb. We are getting link flaps and we suspect that it's a speed issue between the two. However, I cannot find how to set the speed on the old OS of the 3508 switch.
Below is a show version of the 3508 switch.
LR0007>show ver
Cisco Internetwork Operating System Software
IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5)WC17, RELE ASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Tue 13-Feb-07 15:04 by antonino
Image text-base: 0x00003000, data-base: 0x00352924
ROM: Bootstrap program is C3500XL boot loader
LR0007 uptime is 43 weeks, 6 days, 23 hours, 19 minutes
System returned to ROM by power-on
System restarted at 09:36:48 EST Thu Feb 16 2012
System image file is "flash:c3500xl-c3h2s-mz.120-5.WC17.bin"
cisco WS-C3508G-XL (PowerPC403) processor (revision 0x01) with 8192K/1 024K bytes of memory.
Processor board ID CSG0735P0WC, with hardware revision 0x01
Last reset from power-on
Processor is running Enterprise Edition Software
Cluster command switch capable
Cluster member switch capable
8 Gigabit Ethernet/IEEE 802.3 interface(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:0D:65:21:07:C0
Motherboard assembly number: 73-3985-10
Power supply part number: 34-1000-01
Motherboard serial number: CAT07350870
Power supply serial number: APQ072800B4
Model revision number: P0
Motherboard revision number: A0
Model number: WS-C3508G-XL-EN
System serial number: CSG0735P0WC
Configuration register is 0xF
And here are the commans in conf t
LR0007(config)# int gi0/4
LR0007(config-if)#?
Interface configuration commands:
arp Set arp type (arpa, probe, snap) or timeout
bandwidth Set bandwidth informational parameter
carrier-delay Specify delay for interface transitions
cdp CDP interface subcommands
custom-queue-list Assign a custom queue list to an interface
default Set a command to its defaults
delay Specify interface throughput delay
description Interface specific description
duplex Configure duplex operation.
exit Exit from interface configuration mode
fair-queue Enable Fair Queuing on an Interface
flowcontrol Configure flow control operation.
help Description of the interactive help system
hold-queue Set hold queue depth
ip IP interface commands
keepalive Enable keepalive
load-interval Specify interval for load calculation for an interface
logging Configure logging for interface
loopback Configure internal loopback on an interface
mac-address Manually set interface MAC address
max-reserved-bandwidth Maximum Reservable Bandwidth on an Interface
mtu Set the interface Maximum Transmission Unit (MTU)
mvr MVR per port configuration
negotiation Select Autonegotiation mode
no Negate a command or set its defaults
port Perform switch port configuration
priority-group Assign a priority group to an interface
random-detect Enable Weighted Random Early Detection (WRED) on an Interface
rmon Configure Remote Monitoring on an interface
service-policy Configure QoS Service Policy
shutdown Shutdown the selected interface
snmp Modify SNMP interface parameters
spanning-tree Spanning Tree Subsystem
switchport Set switching mode characteristics
timeout Define timeout values for this interface
transmit-interface Assign a transmit interface to a receive-only interface
tx-queue-limit Configure card level transmit queue limit
udld Configure UDLD enabled or disabled and ignore global UDLD setting
Thanks for all of your help. this forum is great for stuff like this.
Jason Alge
