Buy or Renew
Buy or Renew
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
1140
Views
3
Helpful
17
Replies

show platform software trace message smd switch active -Cisco 9300

Go to solution
Mukesh-Kumar
Level 1
Level 1

‎06-04-2024 07:44 AM

show platform software trace message smd switch active not available on Cisco 9300 17.09.05 CAT9K_IOSXE

 

#show platform software trace  ?

context Show btrace global context
counter Show counter value of modules
level Show trace levels

Labels:
0 Helpful
1 Accepted Solution

Accepted Solutions

Go to solution
MHM Cisco World
VIP
VIP
In response to Mukesh-Kumar

‎06-07-2024 01:05 AM 

show logging process smd reverse <<- run this show additional to two commands I suggest above

MHM 

View solution in original post

0 Helpful
17 Replies 17

Go to solution
MHM Cisco World
VIP
VIP

‎06-04-2024 08:39 AM

#set platform software trace smd switch active R0 dot1x-all debug

And 

#set platform software trace smd switch active R0 radius debug

Try above commands

MHM

0 Helpful

Go to solution
Mukesh-Kumar
Level 1
Level 1
In response to MHM Cisco World

‎06-04-2024 10:16 AM

Thank you @Reza Sharifi @MHM Cisco World  for your quick support.  However, the command is still not working on the particular platform.  

Is there any other command showing the same for dot1x debugs ??

Thank you.

0 Helpful

Go to solution
MHM Cisco World
VIP
VIP
In response to Mukesh-Kumar

‎06-04-2024 10:24 AM

did the command enter without any error ?

MHM

0 Helpful

Go to solution
Mukesh-Kumar
Level 1
Level 1

‎06-04-2024 10:30 AM

@MHM Cisco World  

- No error on entering below commands. 

#set platform software trace smd switch active R0 dot1x-all debug
#set platform software trace smd switch active R0 radius debug

However, still, I can't run the command "show platform software trace message smd switch active" .  There is not "message" keyword after "trace"

ISETestSwitch-3#show platform software trace message smd switch active
                                                                        ^
% Invalid input detected at '^' marker.

0 Helpful

Go to solution
MHM Cisco World
VIP
VIP
In response to Mukesh-Kumar

‎06-04-2024 10:46 AM

#set platform software trace smd switch active R0 dot1x-all debug
#set platform software trace smd switch active R0 radius debug

Try get dot1x work and debug will appear I think without need of show

MHM

0 Helpful

Go to solution
Mukesh-Kumar
Level 1
Level 1
In response to MHM Cisco World

‎06-04-2024 10:49 AM

@MHM Cisco World Thank you very much for your time and quick support.  I will get back to you.

Go to solution
Reza Sharifi
Hall of Fame
Hall of Fame
In response to Mukesh-Kumar

‎06-04-2024 12:39 PM

Also, check your license level and make sure you have "network-essentials"

"sh ver" should show you that.

HTH

0 Helpful

Go to solution
Mukesh-Kumar
Level 1
Level 1
In response to Reza Sharifi

‎06-06-2024 09:19 AM

@Reza Sharifi We have smart license subscription with network-advantage. 

0 Helpful

Go to solution
Mukesh-Kumar
Level 1
Level 1
In response to MHM Cisco World

‎06-06-2024 09:18 AM

@MHM Cisco World No, that didn't resolve the issue. It didn't work.

0 Helpful

Go to solution
MHM Cisco World
VIP
VIP
In response to Mukesh-Kumar

‎06-07-2024 01:05 AM 

show logging process smd reverse <<- run this show additional to two commands I suggest above

MHM 

0 Helpful

Go to solution
Mukesh-Kumar
Level 1
Level 1
In response to MHM Cisco World

‎06-07-2024 04:38 AM

Thank you @MHM Cisco World  I will update you by today.

Go to solution
Mukesh-Kumar
Level 1
Level 1
In response to MHM Cisco World

‎06-07-2024 06:29 AM

@MHM Cisco World Thank you very much for your quick update and support.

The command does pulls the output for the last 10 minutes, as per below. 

#show logging process smd reverse
Logging display requested on 2024/06/07 07:37:26 (EST) for Hostname: [xxxxxxx], Model: [C9300-48U], Version: [17.09.05], SN: [FOCXXXXXX], MD_SN: [FCXXXXXX]

Displaying logs from the last 0 days, 0 hours, 10 minutes, 0 seconds
executing cmd on chassis 1 ...
===========================================================
UTM [LUID NOT FOUND] .............. 0
UTM [PCAP] ........................ 0
UTM [MARKER] ...................... 0
UTM [APP CONTEXT] ................. 0
UTM [TDL TAN] ..................... 13
UTM [MODULE ID] ................... 0
UTM [DYN LIB] ..................... 0
UTM [PLAIN TEXT] .................. 259
UTM [ENCODED] ..................... 84086
UTM [Skipped / Rendered / Total] .. 83683 / 675 / 84358
Last UTM TimeStamp ................ 2024/06/07 07:37:25.285197109
First UTM TimeStamp ............... 2024/06/07 05:35:19.762653527
===========================================================
----------------- Decoder Output Information --------------
===========================================================
MRST Filter Rules ...... 1
UTM Process Filter ..... smd
Total UTM To Process ... 84358
Total UTF To Process ... 1
Num of Unique Streams .. 1
===========================================================
----------------- Decoder Input Information ---------------
===========================================================
======= Unified Trace Decoder Information/Statistics ======
===========================================================
2024/06/07 07:36:57.187226352 {smd_R0-0}{1}: [errmsg] [23716]: (note): %SESSION_MGR-5-FAIL: R0/0: sessmgrd: Authorization failed or unapplied for client (006b.f126.1e6a) on Interface GigabitEthernet1/0/1 AuditSessionID D6581EAC0000219AF2805A99. Failure reason: Authc fail. Authc failure reason: Cred Fail.
2024/06/07 07:36:57.187148356 {smd_R0-0}{1}: [mab] [23716]: (info): [006b.f126.1e6a:Gi1/0/1] Freed MAB client context
2024/06/07 07:36:57.187125130 {smd_R0-0}{1}: [mab] [23716]: (info): [006b.f126.1e6a:Gi1/0/1] MAB success: get auth state TERMINATE
2024/06/07 07:36:57.187122527 {smd_R0-0}{1}: [mab] [23716]: (info): [006b.f126.1e6a:Gi1/0/1] Received ABORT event from Auth Mgr for (006b.f126.1e6a)
2024/06/07 07:36:57.186841263 {smd_R0-0}{1}: [mab] [23716]: (info): [006b.f126.1e6a:Gi1/0/1] Received event 'MAB_RESULT' on (006b.f126.1e6a)
2024/06/07 07:36:57.186686564 {smd_R0-0}{1}: [errmsg] [23716]: (note): %MAB-5-FAIL: R0/0: sessmgrd: Authentication failed for client (006b.f126.1e6a) with reason (Cred Fail) on Interface Gi1/0/1 AuditSessionID D6581EAC0000219AF2805A99
2024/06/07 07:36:57.186658100 {smd_R0-0}{1}: [mab] [23716]: (info): [006b.f126.1e6a:Gi1/0/1] MAB received an Access-Reject for 0x0A00004D (006b.f126.1e6a)
2024/06/07 07:36:57.186545159 {smd_R0-0}{1}: [radius] [23716]: (ERR): Failed to mark Identifier for reuse
2024/06/07 07:36:57.186544792 {smd_R0-0}{1}: [radius] [23716]: (ERR): RSPE- Set Identifier Free for Reuse : Input Validation Failed Level-2
2024/06/07 07:36:57.186530794 {smd_R0-0}{1}: [radius] [23716]: (info): Valid Response Packet, Free the identifier
2024/06/07 07:36:57.186452360 {smd_R0-0}{1}: [radius] [23716]: (info): RADIUS: Message-Authenticator[80] 18 ...
2024/06/07 07:36:57.186441429 {smd_R0-0}{1}: [radius] [23716]: (info): RADIUS: authenticator 56 7f 10 2a 48 56 e2 40 - 44 ec 6b 0a a3 9a 28 1d

------and in the end 


Found 1 UTF Streams
Unified Decoder Library Init .. DONE.

Further, I just found another link but I do not have access somehow to the pdf, that is share in the community .

Cat 9300 and no debug output - Cisco Community

https://community.cisco.com/t5/switching/cat-9300-and-no-debug-output/td-p/3712653

MukeshKumar_0-1717766932102.png

 

0 Helpful

Go to solution
Mukesh-Kumar
Level 1
Level 1
In response to MHM Cisco World

‎06-07-2024 06:54 AM

Hello @MHM Cisco World @

Thank you very much for your great support and time.

Upon running the command, I do see the output for last 10 minutes apparently being pulled out.

#show logging process smd reverse
Logging display requested on 2024/06/07 07:41:27 (EST) for Hostname: [ TestWXXX], Model: [C9300-48U], Version: [17.09.05], SN: [FOCxxxxx], MD_SN: [FCWxxxxxx]

Displaying logs from the last 0 days, 0 hours, 10 minutes, 0 seconds
executing cmd on chassis 1 ...
===========================================================
UTM [LUID NOT FOUND] .............. 0
UTM [PCAP] ........................ 0
UTM [MARKER] ...................... 0
UTM [APP CONTEXT] ................. 0
UTM [TDL TAN] ..................... 13
UTM [MODULE ID] ................... 0
UTM [DYN LIB] ..................... 0
UTM [PLAIN TEXT] .................. 275
UTM [ENCODED] ..................... 97189
UTM [Skipped / Rendered / Total] .. 95474 / 2003 / 97477
Last UTM TimeStamp ................ 2024/06/07 07:41:26.303957673
First UTM TimeStamp ............... 2024/06/07 05:35:19.762653527
===========================================================
----------------- Decoder Output Information --------------
===========================================================
MRST Filter Rules ...... 1
UTM Process Filter ..... smd
Total UTM To Process ... 97477
Total UTF To Process ... 1
Num of Unique Streams .. 1
===========================================================
----------------- Decoder Input Information ---------------
===========================================================
======= Unified Trace Decoder Information/Statistics ======
===========================================================
2024/06/07 07:41:18.804476009 {smd_R0-0}{1}: [dot1x] [23716]: (info): [001b.4f32.7781:Gi1/0/21] EAPOL packet sent to client
2024/06/07 07:41:18.804467647 {smd_R0-0}{1}: [dot1x] [23716]: (info): [0000.0000.0000:unknown] Pkt body: 01 01 00 05 01
2024/06/07 07:41:18.804463678 {smd_R0-0}{1}: [dot1x] [23716]: (info): [001b.4f32.7781:Gi1/0/21] EAP Packet - REQUEST, ID : 0x1
2024/06/07 07:41:18.804459389 {smd_R0-0}{1}: [dot1x] [23716]: (info): [001b.4f32.7781:Gi1/0/21] Sent EAPOL packet - Version : 3,EAPOL Type : EAP, Payload Length : 5, EAP-Type = Identity
2024/06/07 07:41:18.803752666 {smd_R0-0}{1}: [dot1x] [23716]: (info): [0000.0000.0000:Gi1/0/21] Sending out EAPOL packet
2024/06/07 07:41:18.803748397 {smd_R0-0}{1}: [dot1x] [23716]: (info): [0000.0000.0000:Gi1/0/21] Setting EAPOL eth-type to 0x888e, destination mac to 001b.4f32.7781
2024/06/07 07:41:18.803722295 {smd_R0-0}{1}: [dot1x] [23716]: (info): [001b.4f32.7781:Gi1/0/21] Entering request state
2024/06/07 07:41:18.803706977 {smd_R0-0}{1}: [dot1x] [23716]: (info): [001b.4f32.7781:Gi1/0/21] Connecting authenticating action
2024/06/07 07:41:18.803692312 {smd_R0-0}{1}: [dot1x] [23716]: (info): [001b.4f32.7781:Gi1/0/21] Authenticating state entered
2024/06/07 07:41:18.803685181 {smd_R0-0}{1}: [dot1x] [23716]: (info): [001b.4f32.7781:Gi1/0/21] Posting RX_REQ on Client
2024/06/07 07:41:18.803677274 {smd_R0-0}{1}: [dot1x] [23716]: (info): [001b.4f32.7781:Gi1/0/21] Restart connecting
2024/06/07 07:41:18.803671061 {smd_R0-0}{1}: [dot1x] [23716]: (info): [001b.4f32.7781:Gi1/0/21] Enter connecting state
2024/06/07 07:41:18.803662825 {smd_R0-0}{1}: [dot1x] [23716]: (info): [001b.4f32.7781:Gi1/0/21] Posting !EAP_RESTART on Client
2024/06/07 07:41:18.803473471 {smd_R0-0}{1}: [dot1x] [23716]: (info): [001b.4f32.7781:Gi1/0/21] Dot1x authentication started for (001b.4f32.7781)
2024/06/07 07:41:18.803442755 {smd_R0-0}{1}: [dot1x] [23716]: (info): [001b.4f32.7781:Gi1/0/21] Entering idle state
2024/06/07 07:41:18.803433348 {smd_R0-0}{1}: [dot1x] [23716]: (info): [001b.4f32.7781:Gi1/0/21] Entering init state
2024/06/07 07:41:18.803373590 {smd_R0-0}{1}: [dot1x] [23716]: (info): [001b.4f32.7781:Gi1/0/21] Sending create new context event to EAP for 0xD4000939 (001b.4f32.7781)
2024/06/07 07:41:18.803363221 {smd_R0-0}{1}: [dot1x] [23716]: (info): [001b.4f32.7781:Gi1/0/21] Entering restart state
2024/06/07 07:41:18.803355176 {smd_R0-0}{1}: [dot1x] [23716]: (info): [001b.4f32.7781:Gi1/0/21] Setting Auth state to disconnected
2024/06/07 07:41:18.803344736 {smd_R0-0}{1}: [dot1x] [23716]: (info): [001b.4f32.7781:Gi1/0/21] Initialising auth state
2024/06/07 07:41:17.424368004 {smd_R0-0}{1}: [dot1x] [23716]: (info): [006b.f126.1e6a:Gi1/0/1] EAPOL packet sent to client
2024/06/07 07:41:17.424360884 {smd_R0-0}{1}: [dot1x] [23716]: (info): [0000.0000.0000:unknown] Pkt body: 01 02 00 05 01
2024/06/07 07:41:17.424357297 {smd_R0-0}{1}: [dot1x] [23716]: (info): [006b.f126.1e6a:Gi1/0/1] EAP Packet - REQUEST, ID : 0x2
2024/06/07 07:41:17.424353413 {smd_R0-0}{1}: [dot1x] [23716]: (info): [006b.f126.1e6a:Gi1/0/1] Sent EAPOL packet - Version : 3,EAPOL Type : EAP, Payload Length : 5, EAP-Type = Identity
2024/06/07 07:41:17.423923514 {smd_R0-0}{1}: [dot1x] [23716]: (info): [0000.0000.0000:Gi1/0/1] Sending out EAPOL packet
2024/06/07 07:41:17.423921259 {smd_R0-0}{1}: [dot1x] [23716]: (info): [0000.0000.0000:Gi1/0/1] Setting EAPOL eth-type to 0x888e, destination mac to 006b.f126.1e6a

Further, I just found another link given below.  However, I can't access the Cisco live mentioned in the post.  Here is the snapshot from the link. @Nadav 

MukeshKumar_0-1717768357931.png

 

Cat 9300 and no debug output - Cisco Community

https://community.cisco.com/t5/switching/cat-9300-and-no-debug-output/td-p/3712653

Customers Also Viewed These Support Documents
Review Cisco Networking for a $25 gift card