cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
Join Customer Connection to register!
3233
Views
5
Helpful
2
Replies
johnlloyd_13
Engager

SNMP Traps on Cisco 2911

hi all,

i'm configuring SNMP on a 2911 router.           

snmp-server view SNMP_RO system included

snmp-server view SNMP_RO interfaces included

snmp-server view SNMP_RO ifMIB included

snmp-server community 5nmpR0 view SNMP_RO ro 33

access-list 33 permit 10.10.1.140 log

access-list 33 deny any log

snmp-server host 10.10.1.140 5nmpR0

when i issued snmp-server enable traps it generated a lot of SNMP related lines.

is this command necessary? or will the community SNMP community string and host is enough?

snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart

snmp-server enable traps vrrp

snmp-server enable traps flowmon

snmp-server enable traps transceiver all

snmp-server enable traps ds1

snmp-server enable traps call-home message-send-fail server-fail

snmp-server enable traps tty

snmp-server enable traps eigrp

snmp-server enable traps ospf state-change

snmp-server enable traps ospf errors

snmp-server enable traps ospf retransmit

snmp-server enable traps ospf lsa

snmp-server enable traps ospf cisco-specific state-change nssa-trans-change

snmp-server enable traps ospf cisco-specific state-change shamlink interface

snmp-server enable traps ospf cisco-specific state-change shamlink neighbor

snmp-server enable traps ospf cisco-specific errors

snmp-server enable traps ospf cisco-specific retransmit

snmp-server enable traps ospf cisco-specific lsa

snmp-server enable traps gatekeeper

snmp-server enable traps xgcp

snmp-server enable traps license

snmp-server enable traps envmon

snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config

snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up

snmp-server enable traps flash insertion removal

snmp-server enable traps auth-framework sec-violation

snmp-server enable traps c3g

snmp-server enable traps ds3

snmp-server enable traps entity-sensor threshold

snmp-server enable traps adslline

snmp-server enable traps vdsl2line

snmp-server enable traps icsudsu

snmp-server enable traps isdn call-information

snmp-server enable traps isdn layer2

snmp-server enable traps isdn chan-not-avail

snmp-server enable traps isdn ietf

snmp-server enable traps ds0-busyout

snmp-server enable traps ds1-loopback

snmp-server enable traps energywise

snmp-server enable traps vstack

snmp-server enable traps mac-notification

snmp-server enable traps bgp cbgp2

snmp-server enable traps isis

snmp-server enable traps ospfv3 state-change

snmp-server enable traps ospfv3 errors

snmp-server enable traps aaa_server

snmp-server enable traps atm subif

snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency

snmp-server enable traps memory bufferpeak

snmp-server enable traps cnpd

snmp-server enable traps config-copy

snmp-server enable traps config

snmp-server enable traps config-ctid

snmp-server enable traps entity

snmp-server enable traps fru-ctrl

snmp-server enable traps resource-policy

snmp-server enable traps event-manager

snmp-server enable traps frame-relay multilink bundle-mismatch

snmp-server enable traps frame-relay

snmp-server enable traps frame-relay subif

snmp-server enable traps hsrp

snmp-server enable traps ipmulticast

snmp-server enable traps msdp

snmp-server enable traps mvpn

snmp-server enable traps nhrp nhs

snmp-server enable traps nhrp nhc

snmp-server enable traps nhrp nhp

snmp-server enable traps nhrp quota-exceeded

snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message

snmp-server enable traps pppoe

snmp-server enable traps cpu threshold

snmp-server enable traps rsvp

snmp-server enable traps syslog

snmp-server enable traps l2tun session

snmp-server enable traps l2tun pseudowire status

snmp-server enable traps vtp

snmp-server enable traps waas

snmp-server enable traps ipsla

snmp-server enable traps dial

snmp-server enable traps dsp card-status

snmp-server enable traps dsp oper-state

snmp-server enable traps dsp video-usage

snmp-server enable traps dsp video-out-of-resource

snmp-server enable traps ethernet cfm alarm

snmp-server enable traps rf

snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down

snmp-server enable traps ccme

snmp-server enable traps srst

snmp-server enable traps voice

snmp-server enable traps dnis

2 REPLIES 2
Reza Sharifi
Hall of Fame Expert

Hi John,

I believe, if you don't specify a specific trap, it will enable all options.

The snmp-server enable traps snmpcommand is used in conjunction with the snmp-server hostcommand. Use the snmp-server host command to specify which host or hosts receive SNMP notifications. In order to send notifications, you must configure at least one snmp-server hostcommand.

For a host to receive a notification controlled by this command, you must enable both the snmp-server enable traps command and the snmp-server hostcommand for that host. If the notification type is not controlled by this command, you must enable the appropriate snmp-server host command only.

http://www.cisco.com/en/US/docs/ios-xml/ios/snmp/command/nm-snmp-cr-s3.html

HTH

hi reza,

thanks for your feedback!

will negate the snmp trap line first and see how it goes.