Solved: Re: Stack Compatibility Between CISCO 3750X AND CISCO 3750G

safwan riyazudeen · ‎10-09-2013

Hi Friends

We Have an exsisting stack switch, with 3750G . i Need to add new 12 Port SFP switch to the exsisting stack.

Exsisting stack switch software and ios Image is psted below

Switch Ports Model SW Version SW Image

------ ----- ----- ---------- ----------

* 1 12 WS-C3750G-12S 12.2(52)SE C3750-IPSERVICESK9-M

2 28 WS-C3750G-24TS-1U 12.2(52)SE C3750-IPSERVICESK9-M

3 28 WS-C3750G-24TS-1U 12.2(52)SE C3750-IPSERVICESK9-M

4 28 WS-C3750G-24TS-1U 12.2(52)SE C3750-IPSERVICESK9-M

My New SFP Switch is 3750X-12 ports switch, i tried upgrading the new SFP Switch with the same image as in master.

But after upgrading when i boot from the upgraded image i am getting an below error

Error:hardware not supported by firmware

Try loading newer software instead

System resetting....

My Doubts

Whether this Hardwares are compatible to add (Cisco 3750X & Cisco 3750G)

what is the least Ios requirement i needed in Cisco 3750X to add it to 3750G stack

I seen several forums telling that we need atleast 12.2(58) ios and few stating 12.2(53) ios. Please confirm the correct hardware and software requirement

Thanks for youe help in Advance

Guys.

Regards

Safwan

Marvin Rhoads · ‎10-09-2013

You have to have at least 12.2(53) to support the 3750X hardware. Reference.

12.2(55)SE8 would be recommended based on general stability and bug fixes.

View solution in original post

Leo Laohoo · ‎10-09-2013

You have to have at least 12.2(53) to support the 3750X hardware. Reference.
 12.2(55)SE8 would be recommended based on general stability and bug fixes.

Marvin's post is worth it's weight in gold and doesn't deserve a "4" rating.

Alos these 3750G Stack is a core .. (Different buildings connects from here). So its required Layesr 3 capabailites

Could you tell me to run the stack with layser 3 capapbailities, whats the IOS train i need to use on Both switches?

Make sure your 3750X is running the same feature set as the rest of the stack, i. e. IP Services.

View solution in original post

Marvin Rhoads · ‎10-09-2013

You have to have at least 12.2(53) to support the 3750X hardware. Reference.

12.2(55)SE8 would be recommended based on general stability and bug fixes.

safwan riyazudeen · ‎10-09-2013

Thanks marvin..

for you rprompt response

its very useful.

So To Connect the 3750X to 3750G stack i need minimum 12.2(53)

Excluding this we have any other pre requsities??

Wilson Bonilla · ‎10-09-2013

Hello Safwan.

12.2(53) might be available for some 3750x and not for other in the cisco support website... so I would say:

1- Currently at least you will need to have 12.2(55).

2- For 3750x platform note that all iOS images are either universal or ip base.

3- For 3750G platform note that all iOS images are either ip base or ip services.

Having said that, you will need to run at least 12.2(55) train in both 3750G and 3750X switches. If you need layer 3 capabilities chose universal for 3760x and ipservices for 3750G.

Regards.

Wilson B.

safwan riyazudeen · ‎10-09-2013

Hi Wilson,

Thankd for your Reply

Yes..

Currently the 3750G Stack having ipservice image(C3750-IPSERVICESK9-M) and new 3750X has universal image(

c3750e-universalk9-mz.122-58.SE2)

when i try to downrage the 3750X to (C3750-IPSERVICESK9-M) it throwed me an hardware error

Error:hardware not supported by firmware

Try loading newer software instead

System resetting....

So to get this working

1) i need to upgrade my current exsisting stack to 12.2(55) currently its running 12.2(52)

2)downgrade the new cisco 3750X to ios version 12.2(55)

??

Alos these 3750G Stack is a core .. (Different buildings connects from here). So its required Layesr 3 capabailites

Could you tell me to run the stack with layser 3 capapbailities, whats the IOS train i need to use on Both switches?

Reagdrs

SAfwan

Leo Laohoo · ‎10-09-2013

You have to have at least 12.2(53) to support the 3750X hardware. Reference.
 12.2(55)SE8 would be recommended based on general stability and bug fixes.

Marvin's post is worth it's weight in gold and doesn't deserve a "4" rating.

Alos these 3750G Stack is a core .. (Different buildings connects from here). So its required Layesr 3 capabailites

Could you tell me to run the stack with layser 3 capapbailities, whats the IOS train i need to use on Both switches?

Make sure your 3750X is running the same feature set as the rest of the stack, i. e. IP Services.

safwan riyazudeen · ‎10-10-2013

Leo,

Thanks for your Response.

For running Layer 3 we dont require any special ios??

So in a nutshell

current IOS

Old 3750G Stack:12.2(52)SE -C3750-IPSERVICESK9-M

New 3750X STACK:3750e-universalk9-mz.122-58.SE2

1) if i use 12.2(58) - c3750-ipservicesk9-mz.122-55.SE8.bin same ios in both 3750G & 3750X Switch , it will work as stack ?

Thanks to confirm

Joseph W. Doherty · ‎10-10-2013

Disclaimer

The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.

Liability Disclaimer

In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.

Posting

To run IP Services on the 3750X, you'll need the universal image AND an IP Service feature license. (The license is something "new" to the -E/-X 3750, i.e. not found on your 3750Gs.)

It's possible to run different feature sets within a 3750 stack, but not sure if there's any special requirements for a mixed stack (i.e. original series 3750s and the later -E/-X series).

PS:

Also BTW, mixed 3750 stacks "take away" some of the advantages of the -E/-X 3750 stacks.

Leo Laohoo · ‎10-10-2013

1)  if i use 12.2(58) -  c3750-ipservicesk9-mz.122-55.SE8.bin same ios in both 3750G & 3750X Switch , it will work as stack ?

You will not be able to get the 3750X to boot up or load this filename because it's designed for 3750G.

For running Layer 3 we dont require any special ios??

As what Joseph has stated, 3750X needs to run the "universal" plus you need to ensure the 3750X has the "IP Services" license installed. Use the command "sh license" to verify on the 375X.

safwan riyazudeen · ‎10-16-2013

Hi Leo,

Thanks for your Info..

Please find the show licensce output from the New switch 3750X switch. Will it has the required licence?

Switch#sh license

Index 1 Feature: ipservices

Period left: 8 weeks 4 days

License Type: Evaluation

License State: Active, Not in Use, EULA not accepted

License Priority: None

License Count: Non-Counted

Index 2 Feature: ipbase

Period left: Life time

License Type: Permanent

License State: Active, In Use

License Priority: Medium

License Count: Non-Counted

Bcoz when i gave the same command in Core switch (3750G-12 port ) it is showing as

% License not supported on this device

So currently if i use 12.2.55-SE5 Software version in all switches and use

below IOS image in

WS-C3750X-12S : c3750e-universalk9-mz.122-55.SE5.bin

and below image in

WS-C3750G-12S : c3750-ipservicesk9-mz.122-55.SE5.bin

can i stack it sucessfully or am i missing smoenthing??

Joseph W. Doherty · ‎10-16-2013

Disclaimer

The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.

Liability Disclaimer

In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.

Posting

Please find the show licensce output from the New switch 3750X switch. Will it has the required licence?

Switch#sh license

Index 1 Feature: ipservices

Period left: 8 weeks 4 days

License Type: Evaluation

License State: Active, Not in Use, EULA not accepted

License Priority: None

License Count: Non-Counted

Yes and no. You're running an evaluation license for IP Services, which means you have the right license but it will expire in 8 weeks and 4 days (then it will be just IP Base).

Bcoz when i gave the same command in Core switch (3750G-12 port ) it is showing as

% License not supported on this device

As I noted in my earlier post, original series 3750s don't support hardware licensing. Legally you need "paper" licenses. Technically, feature set depends on installed image (and yours shows IP Services).

So currently if i use 12.2.55-SE5 Software version in all switches and use

below IOS image in

WS-C3750X-12S : c3750e-universalk9-mz.122-55.SE5.bin

and below image in

WS-C3750G-12S : c3750-ipservicesk9-mz.122-55.SE5.bin

can i stack it sucessfully or am i missing smoenthing??

You should be able to stack them, but again, you're 3750X's IP Service license will expire.

safwan riyazudeen · ‎10-16-2013

Hi Joesph

Thanks for your Replies.

Correct me if i am wrong

1) This stack option will work, But since we have an Evalautation licence it will stop working after 8 weeks? If so, what i need to do get the permanenet licsense?

2) 3750G's doesnt support Hardware licsensing, But since feature set depends on the Ios image, And we are running an ip services image set, Which is required for this stack Connectivity, So this hardware liscensing for 3750G wont be an problem correct?

Please add , if i missed something

Regards

Safwan

Joseph W. Doherty · ‎10-16-2013

Disclaimer

The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.

Liability Disclaimer

In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.

Posting

1) This stack option will work, But since we have an Evalautation licence it will stop working after 8 weeks? If so, what i need to do get the permanenet licsense?

Yes, evaluation license will stop after 8 weeks. You can purchase a licenses for IP Services.

2) 3750G's doesnt support Hardware licsensing, But since feature set depends on the Ios image, And we are running an ip services image set, Which is required for this stack Connectivity, So this hardware liscensing for 3750G wont be an problem correct?

IP Services isn't required for stacking, but I don't know if original series running IP Services will work with -X with IP Base.

Sanjay Shaw · ‎10-16-2013

Once you add the switch with evaluation licence it will work. But if you have any ipservices features command in the Master switch running it will only be supported till 8 weeks and 4 days with this in stack.After that this switch will be no more in stack.

safwan riyazudeen · ‎10-17-2013

Guys,

I Tried to Simulate the Stacking, with the spair 3750G Switch with the new 3750X. i am Successfuly able to stack it.

Switch#Sh SwItch

Switch/Stack Mac Address : 10f3.119e.d280

H/W Current

Switch# Role Mac Address Priority Version State

----------------------------------------------------------

*1 Master 10f3.119e.d280 5 1 Ready

2 Member 3cdf.1e59.2780 1 0 Ready

Switch#sh vers

Switch#sh version

Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE5, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Thu 09-Feb-12 18:14 by prod_rel_team

Image text-base: 0x00003000, data-base: 0x02800000

ROM: Bootstrap program is C3750E boot loader

BOOTLDR: C3750E Boot Loader (C3750X-HBOOT-M) Version 12.2(58r)SE, RELEASE SOFTWARE (fc1)

Switch uptime is 3 hours, 49 minutes

System returned to ROM by power-on

System image file is "flash:c3750e-universalk9-mz.122-55.SE5.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

License Level: ipbase

License Type: Permanent

Next reload license Level: ipbase

cisco WS-C3750X-12S (PowerPC405) processor (revision A0) with 524288K bytes of memory.

Processor board ID FDO1707Z0CG

Last reset from power-on

2 Virtual Ethernet interfaces

1 FastEthernet interface

44 Gigabit Ethernet interfaces

2 Ten Gigabit Ethernet interfaces

The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address : 10:F3:11:9E:D2:80

Motherboard assembly number : 73-13329-04

Motherboard serial number : FDO17061NB8

Model revision number : A0

Motherboard revision number : A0

Model number : WS-C3750X-12S-S

Daughterboard assembly number : 800-32727-03

Daughterboard serial number : FDO17340ZPC

System serial number : FDO1707Z0CG

Top Assembly Part Number : 800-35090-04

Top Assembly Revision Number : B0

Version ID : V03

CLEI Code Number : CMMFG00ARC

Hardware Board Revision Number : 0x04

Switch Ports Model SW Version SW Image

------ ----- ----- ---------- ----------

* 1 18 WS-C3750X-12S 12.2(55)SE5 C3750E-UNIVERSALK9-M

2 28 WS-C3750G-24TS-1U 12.2(55)SE5 C3750-IPSERVICESK9-M

Switch 02

---------

Switch Uptime : 3 hours, 43 minutes

Base ethernet MAC Address : 3C:DF:1E:59:27:80

Motherboard assembly number : 73-10219-07

Power supply part number : 341-0098-02

Motherboard serial number : FOC13441NA1

Power supply serial number : AZS1342011F

Model revision number : F0

Motherboard revision number : D0

Model number : WS-C3750G-24TS-S1U

System serial number : FOC1344Y1AU

Top assembly part number : 800-26859-01

Top assembly revision number : E0

Version ID : V03

CLEI Code Number : CNMWS00ARC

Configuration register is 0xF

Below is the Ios i used in Both Switches

C3750X(12 PORT) - WS-C3750X-12S : c3750e-universalk9-mz.122-55.SE5.bin

C37504(24PORT) - WS-C3750G-12S : c3750-ipservicesk9-mz.122-55.SE5.bin

But My final Doubt is still unclear,

1) In c3750X New switch i have only ipbase license(permanent) , ipservices license is in evaluation. Do i need Ipservices permanent License , in C3750X Stack or with ipbase license itself this stack comibnation will work?

2) Existing C3750G core stack Doesnt have support license(please see below error) , so will it create any issues or i can add the 3750X Switch with these Stack with 3750x(ipbase license) Alone?

FRLB_BK1_COR3750_01#sh license

% License not supported on this device

FRLB_BK1_COR3750_01#

Kindly clarify the below doubts