09-15-2016 08:01 AM - edited 03-08-2019 07:26 AM
HI. Please help me. There was a problem with WS-C4510R-E. After updating to firmware cat4500e-entservicesk9-mz.152-2.E2.bin does not study the client MAC address (connected directly to the port), the port rises normally full in 1000, there are no errors, the MAC table is full.
When you type the command:
sh mac address-table int gi
Multicast Entries
vlan mac address type ports
MAC does not see
When configuring port security MAC remembers
sh mac address-table int gi8/7
Unicast Entries
vlan mac address type protocols port
---------+---------------+--------+---------------------+-------------------------
9 xxxxxxxxxxxx static ip,ipx,assigned,other GigabitEthernet
Why is this happening? Port access
09-15-2016 10:41 AM
Hi,
Is this switch in production ?
Did you try clearing the mac add table ?
Regards,
Harsha
09-15-2016 11:24 PM
Yes this a switch in production and I cleared the table MAC
09-15-2016 05:02 PM
Post the complete output to the command "sh interface Gi 8/7".
09-15-2016 11:22 PM
sh int gi8/7
GigabitEthernet8/7 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet Port, address is 0023.eb9e.3a76 (bia 0023.eb9e.3a76)
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto-speed, link type is auto, media type is 10/100/1000-TX
input flow-control is off, output flow-control is off
ARP type: ARPA, ARP Timeout 04:00:00
Last input 03:10:26, output never, output hang never
Last clearing of "show interface" counters 20:35:46
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 0 bits/sec, 0 packets/sec
30 second output rate 0 bits/sec, 0 packets/sec
59211 packets input, 5828825 bytes, 0 no buffer
Received 59212 broadcasts (31982 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
199195 packets output, 25531819 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
At the moment down
09-16-2016 12:42 AM
GigabitEthernet8/7 is down, line protocol is down (notconnect)
Makes sense. Layer 1 is down, so MAC address is not kept.
09-16-2016 01:20 AM
He excluded port-sec, dropping port settings to default and then setting it:
interface GigabitEthernet8/7
switchport access vlan *
switchport mode access
switchport voice vlan *
load-interval 30
spanning-tree portfast
spanning-tree bpduguard enable
end
it worked - the MAC address for the port being studied.
This IOS bug cat4500e-entservicesk9-mz.152-2.E2.bin
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide