I made a upgrade for c7600. However the firmware still on 12.2, on the RSP, and Line Card.
Any one know, If we need to upgrade the firmware too, and what is the procedure...?
hostname#show module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 0 4-subslot SPA Interface Processor-200 7600-SIP-200 xxxxxx
2 0 4-subslot SPA Interface Processor-200 7600-SIP-200 xxxxxx
3 48 CEF720 48 port 1000mb SFP WS-X6748-SFP xxxxxx
5 2 Route Switch Processor 720 (Hot) RSP720-3CXL-GE xxxxxx
6 2 Route Switch Processor 720 (Active) RSP720-3CXL-GE xxxxxx
8 0 4-subslot SPA Interface Processor-400 7600-SIP-400 xxxxxx
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ----- ------------- ------------ -------
1 ccef.486c.4040 to ccef.486c.407f 2.307 15.3(3)S6 15.3(3)S6 Ok
2 ccef.486c.2440 to ccef.486c.247f 2.307 15.3(3)S6 15.3(3)S6 Ok
3 70ca.9b1d.62f8 to 70ca.9b1d.6327 2.4 12.2(18r)S 15.3(3)S Ok
5 c89c.1dfb.c890 to c89c.1dfb.c893 5.12 12.2(33r)SRD 15.3(3)S Ok
6 0022.bde6.9060 to 0022.bde6.9063 5.12 12.2(33r)SRD 15.3(3)S Ok
8 64f6.9d98.1b00 to 64f6.9d98.1b7f 3.4 15.3(3)S6 15.3(3)S6 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1/0 2xOC3 POS SPA SPA-2XOC3-POS xxxxxx1.0 Ok
1/1 4xOC3 POS SPA SPA-4XOC3-POS xxxxxx1.0 Ok
1/2 8xCHT1/E1 SPA SPA-8XCHT1/E1 xxxxxx1.5 Ok
2/0 2xT3E3 SPA SPA-2XT3/E3 xxxxxx1.1 Ok
2/1 8xCHT1/E1 SPA SPA-8XCHT1/E1 xxxxxx1.5 Ok
2/2 8xFE TX SPA SPA-8X1FE-TX-V2 xxxxxx1.3 Ok
3 Distributed Forwarding Card WS-F6700-DFC3CXL xxxxxx1.7 Ok
5 Policy Feature Card 3 7600-PFC3CXL xxxxxx1.1 Ok
5 C7600 MSFC4 Daughterboard 7600-MSFC4 xxxxxx1.6 Ok
6 Policy Feature Card 3 7600-PFC3CXL xxxxxx1.1 Ok
6 C7600 MSFC4 Daughterboard 7600-MSFC4 xxxxxx1.6 Ok
8/0 5xGE SPA SPA-5X1GE-V2 xxxxxx1.5 Ok
Mod Online Diag Status
---- -------------------
1 Pass
1/0 Pass
1/1 Pass
1/2 Pass
2 Pass
2/0 Pass
2/1 Pass
2/2 Pass
3 Pass
5 Pass
6 Pass
8 Pass
