username in 9000 switch

[Mbezayiff1]

I have a 9000 switch and when I try to add one user name, it will take it, adding a second or third and it fails with aaa error user5 5, after adding the aaa new-model statement, it will do the same, one name, this is from the CLI

[Reza Sharifi]

What is the switch model you have and what IOS are you running?

Can you post the exact output of the command you apply and the error message?

HTH

[Mbezayiff1]

isco IOS XE Software, Version 16.11.01

Cisco IOS Software [Gibraltar], Catalyst L3 Switch Software (CAT9K_LITE_IOSXE), Version 16.11.1, RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2019 by Cisco Systems, Inc.

Compiled Thu 28-Mar-19 07:19 by mcpre



FIPS: Flash Key Check : Key Not Found, FIPS Mode Not Enabled



% Please answer 'yes' or 'no'.

Would you like to enter the initial configuration dialog? [yes/no]:

% Please answer 'yes' or 'no'.

Would you like to enter the initial configuration dialog? [yes/no]: n



Would you like to terminate autoinstall? [yes]: y



Switch#config t

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#username engineering privilege 15 secret Domino

Switch(config)#



Switch(config)#

Switch(config)#Switch(config)#username triplight privilege 15 secret Earth2wo

^

%.



Switch(config)#$ER_RESET: User triplight failed attempts reset by console

*Aug 30 13:42:59.627: %AAA-5-USER_RESET: User triplight failed attempts reset by^ console



% Invalid input detected at '^' marker.



Switch(config)#username engineering privilege 15 secret Earth2wo

Switch(config)#username triplight privilege 15 secret D0mino

Switch(config)#username Matthew privilege 15 secret H0m2alone

Switch(config)#

*Aug 30 13:47:15.136: %AAA-5-USER_RESET: User Matthew failed attempts reset by console

[Mbezayiff1]

isco IOS XE Software, Version 16.11.01
Cisco IOS Software [Gibraltar], Catalyst L3 Switch Software (CAT9K_LITE_IOSXE), Version 16.11.1, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2019 by Cisco Systems, Inc.
Compiled Thu 28-Mar-19 07:19 by mcpre

FIPS: Flash Key Check : Key Not Found, FIPS Mode Not Enabled

% Please answer 'yes' or 'no'.
Would you like to enter the initial configuration dialog? [yes/no]:
% Please answer 'yes' or 'no'.
Would you like to enter the initial configuration dialog? [yes/no]: n

Would you like to terminate autoinstall? [yes]: y

Switch#config t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#username engineering privilege 15 secret Domino
Switch(config)#

Switch(config)#
Switch(config)#Switch(config)#username triplight privilege 15 secret Earth2wo
                     ^
%.

Switch(config)#$ER_RESET: User triplight failed attempts reset by console
*Aug 30 13:42:59.627: %AAA-5-USER_RESET: User triplight failed attempts reset by^ console

% Invalid input detected at '^' marker.

Switch(config)#username engineering privilege 15 secret Earth2wo
Switch(config)#username triplight privilege 15 secret D0mino
Switch(config)#username Matthew privilege 15 secret H0m2alone
Switch(config)#
*Aug 30 13:47:15.136: %AAA-5-USER_RESET: User Matthew failed attempts reset by console