10-25-2017 11:05 PM - edited 03-08-2019 12:29 PM
I have WLC 2500 , there any many APs air-cap1702i-e-k9 connected with WLC .
I tried to access AP through http with its IP , not display login page for AP
10-25-2017 11:54 PM
@eng_adel273 wrote:
I have WLC 2500 , there any many APs air-cap1702i-e-k9 connected with WLC .
I tried to access AP through http with its IP , not display login page for AP
That's because the AP is being controlled by the WLC. The only way to "access" or configure the AP is through the controller.
10-26-2017 12:36 AM
Thank you for your response
please tell me the step to add new AP and register it in WLC
10-26-2017 12:56 AM
Kindly post the complete output to the following commands:
10-26-2017 01:21 AM
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 8.1.102.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. PIC 20.0
Build Type....................................... DATA + WPS
System Name...................................... H-WLC1
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.30.11
IPv6 Address..................................... ::
Last Reset....................................... Power on reset
System Up Time................................... 77 days 19 hrs 51 mins 43 secs
System Timezone Location......................... (GMT +3:00) Baghdad
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More-- or (q)uit
Configured Country............................... SA - Saudi Arabia
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +26 C
External Temperature............................. +30 C
Fan Status....................................... 3800 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 16
Number of Active Clients......................... 14
Burned-in MAC Address............................ 80:E8:6F:00:01:A0
Maximum number of APs supported.................. 75
System Nas-Id.................................... Hafuf-WLC1
WLC MIC Certificate Types........................ SHA1/SHA2
=================================================
(Cisco Controller) >show time
Time............................................. Thu Oct 26 11:06:36 2017
Timezone delta................................... 0:0
Timezone location................................ (GMT +3:00) Baghdad
NTP Servers
NTP Polling Interval......................... 86400
Index NTP Key Index NTP Server NTP Msg Auth Status
------- ----------------------------------------------------------------------------------
==============================================================
(Cisco Controller) >show interface summary
Number of Interfaces.......................... 18
Interface Name Port Vlan Id IP Address Type Ap Mgr Guest
-------------------------------- ---- -------- --------------- ------- ------ -----
x1 LAG 31 192.168.31.11 Dynamic No No
x2 LAG 37 192.168.37.11 Dynamic No No
x3 LAG 35 192.168.35.11 Dynamic No No
x4 LAG 46 192.168.46.11 Dynamic No No
x5 LAG 36 192.168.36.11 Dynamic No No
x6 LAG 38 192.168.38.11 Dynamic No No
x7 LAG 40 192.168.50.11 Dynamic No No
x8 LAG 33 192.168.33.11 Dynamic No No
x9 LAG 30 192.168.30.11 Static Yes No
x10 LAG 42 192.168.42.11 Dynamic No No
x11 LAG 51 192.168.51.11 Dynamic No No
x12 LAG 41 192.168.41.11 Dynamic No No
x13 LAG 39 192.168.39.11 Dynamic No No
x14 LAG 32 192.168.32.11 Dynamic No No
x15 LAG 34 192.168.34.11 Dynamic No No
10-26-2017 01:37 AM
(Cisco Controller) >show sysinfo;
Incorrect usage. Use the '?' or <TAB> key to list commands.
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 8.1.102.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. PIC 20.0
Build Type....................................... DATA + WPS
System Name...................................... H-WLC1
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.30.11
IPv6 Address..................................... ::
Last Reset....................................... Power on reset
System Up Time................................... 77 days 20 hrs 12 mins 41 secs
System Timezone Location......................... (GMT +3:00) Baghdad
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More-- or (q)uit
Configured Country............................... SA - Saudi Arabia
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +26 C
External Temperature............................. +30 C
Fan Status....................................... 3800 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 16
Number of Active Clients......................... 14
Burned-in MAC Address............................ 80:E8:6F:00:01:A0
Maximum number of APs supported.................. 75
System Nas-Id.................................... H-WLC1
WLC MIC Certificate Types........................ SHA1/SHA2
=============================================================
(Cisco Controller) >show time
Time............................................. Thu Oct 26 11:26:40 2017
Timezone delta................................... 0:0
Timezone location................................ (GMT +3:00) Baghdad
NTP Servers
NTP Polling Interval......................... 86400
Index NTP Key Index NTP Server NTP Msg Auth Status
------- ----------------------------------------------------------------------------------
==========================================================
10-26-2017 03:18 AM
I send the configuration many time , but not appeared
10-26-2017 03:19 AM
Please tell me the steps , I will modify the setting as my case
10-26-2017 12:22 PM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide