WS 6509-E Card status Minfail

[D_Lebedev]

Hi,

I've  Cat. 6509  with minfail status of DF card.

There is no any errors in log and diag logs.

How i can identify this problem?

Thanks.

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  1    8  CEF720 8 port 10GE with DFC            WS-X6708-10GE      SAL1229XU2B

  2   16  SFM-capable 16 port 1000mb GBIC        WS-X6516A-GBIC     SAL1227W6BZ

  3   16  SFM-capable 16 port 1000mb GBIC        WS-X6516A-GBIC     SAL1227W6CD

  4   16  SFM-capable 16 port 1000mb GBIC        WS-X6516A-GBIC     SAL1227W6BS

  5    2  Supervisor Engine 720 (Active)         WS-SUP720-3B       SAL1228WPEB

Mod MAC addresses                       Hw    Fw           Sw           Status

--- ---------------------------------- ------ ------------ ------------ -------

  1  0022.557d.d9d8 to 0022.557d.d9df   1.4   12.2(18r)S1  12.2(33)SXI9 MinFail

  2  0022.554d.2740 to 0022.554d.274f   4.6   7.2(1)       12.2(33)SXI9 Ok

  3  0022.554d.2640 to 0022.554d.264f   4.6   7.2(1)       12.2(33)SXI9 Ok

  4  0022.554d.2500 to 0022.554d.250f   4.6   7.2(1)       12.2(33)SXI9 Ok

  5  0016.46f9.bac0 to 0016.46f9.bac3   5.6   8.5(2)       12.2(33)SXI9 Ok

Mod  Sub-Module                  Model              Serial       Hw     Status

---- --------------------------- ------------------ ----------- ------- -------

  1  Distributed Forwarding Card WS-F6700-DFC3C     SAL1228WULV  1.0    MinFail

  5  Policy Feature Card 3       WS-F6K-PFC3B       SAL1227WATL  2.3    Ok

  5  MSFC3 Daughterboard         WS-SUP720          SAL1228WJ5H  3.1    Ok

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  1    8  CEF720 8 port 10GE with DFC            WS-X6708-10GE      SAL1229XU2B

Mod MAC addresses                       Hw    Fw           Sw           Status

--- ---------------------------------- ------ ------------ ------------ -------

  1  0022.557d.d9d8 to 0022.557d.d9df   1.4   12.2(18r)S1  12.2(33)SXI9 MinFail

Mod  Sub-Module                  Model              Serial       Hw     Status

---- --------------------------- ------------------ ----------- ------- -------

  1  Distributed Forwarding Card WS-F6700-DFC3C     SAL1228WULV  1.0    MinFail

Mod  Online Diag Status

---- -------------------

  1  Pass

[InayathUlla Sharieff]

HI,

the MinFail status may indicate 2 things:

- A Hardware failure on the blade or chassis slot

- Incorrect environmental policies are affecting the switch, and the temperature of the blade is rising, this can cause a MinFail alarm.

In order to verify if the problem is related to a HW problem, would you be able to try module 1 in another slot? for example slot 8, and after it comes up please

capture the following for me:

show module

show logging

show environment temp

show diagnostic result module 8

Action plan:

========

Reseat the Module.

Check the Fan tray

Check if there is any dust on the switch chasis and anything blocking near the switch.

HTH

REgards

Inayath

*Plz rate all usefull posts.

[D_Lebedev]

Logs

[InayathUlla Sharieff · Accepted solution]

Nothing present in the logs.

Core6509#sh environment temp

  VTT 1 outlet temperature: 35C

  VTT 2 outlet temperature: 29C

  VTT 3 outlet temperature: 30C

  module 1 outlet temperature: 51C

  module 1 inlet temperature: 42C

  module 1 aux-1 temperature: 51C

  module 1 aux-2 temperature: 34C

  module 1 asic-1 temperature: 96C>>>> ITs quite high

  module 1 asic-2 temperature: 77C>>>> ITs quite high

I could see that the temperature is getting increased. hence could you check if there is any temperature problem in the server room were this device is located?

Check if anything blocking the Air flow near this module and switch?

HTH

Regards

Inayath

[D_Lebedev]

Thanks a lot.