cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
5557
Views
6
Helpful
5
Replies

WS-C4507R+E - Perform Reload Active Supervisor

Hi Team,

We planning to reload our Supervisor module due to bug CSCuq09636, Currently our switch running with two Supervisor moduels.

Please quide us how to proceed with reload of this Supervisor.

Switch# redundancy force-switchover
Switch# redundancy reload peer


Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 48 10/100/1000BaseT Premium POE E Series WS-X4748-RJ45V+E
2 48 10/100/1000BaseT Premium POE E Series WS-X4748-RJ45V+E
3 6 Sup 7L-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7L-E
4 6 Sup 7L-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7L-E

M MAC addresses Hw Fw Sw Status
--+--------------------------------+---+------------+----------------+---------
1 1.2 Ok
2 Ok
3 3.1 15.0(1r)SG10 03.05.02.E Ok
4 3.1 15.0(1r)SG10 03.05.02.E Ok

Mod Redundancy role Operating mode Redundancy status
----+-------------------+-------------------+----------------------------------
3 Active Supervisor SSO Active
4 Standby Supervisor SSO Standby hot

 

Redundant System Information :

------------------------------
Available system uptime = 1 year, 34 weeks, 1 day, 23 hours, 45 minutes
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = none

Hardware Mode = Duplex
Configured Redundancy Mode = Stateful Switchover
Operating Redundancy Mode = Stateful Switchover
Maintenance Mode = Disabled
Communications = Up

Current Processor Information :
------------------------------
Active Location = slot 3
Current Software state = ACTIVE
Uptime in current state = 1 year, 20 weeks, 1 days, 2 hours, 32 minutes
Image Version = Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.05.02.E RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Tue 12-Mar-14 16:27 by prod_
BOOT = bootflash:cat4500e-universalk9.SPA.03.05.02.E.152-1.E2.bin,1;
Configuration register = 0x2102

Peer Processor Information :
------------------------------
Standby Location = slot 4
Current Software state = STANDBY HOT
Uptime in current state = 1 year, 20 weeks, 1 days, 2 hours, 30 minutes
Image Version = Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.05.02.E RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Tue 12-Mar-14 16:27 by pro
BOOT = bootflash:cat4500e-universalk9.SPA.03.05.02.E.152-1.E2.bin,1;
Configuration register = 0x2102

 

 

5 Replies 5

Leo Laohoo
Hall of Fame
Hall of Fame

I'd upgrade the version of IOS.  

I would like to know procedure for reload SUP module... don't want to disturb with traffic impact.

You can reload the supervisor card(s), but running a buggy train, like 3.5.X, isn't going to do any help.

After reload this switch issue resolved

This is soft parity error detected in Sup. reload of the SUP should fix these logs. no need to worry about the bug.

Review Cisco Networking for a $25 gift card