Tag: "boot_issues" in "Networking Knowledge Base" - Cisco Community

Latest Tagged

The 2600, 3600 and 3700 series routers boot continuously after the Cisco IOS Software upgrade due to... - ( ‎06-22-2009 03:42 PM )

by on

0 Comments 2489 Views

0 Comments

2489 Views

Router boots into boot mode without any errors displayed on the console - ( ‎06-22-2009 04:04 PM )

by on

0 Comments 21780 Views

0 Comments

21780 Views

Continuous boot loop due to insufficient memory - ( ‎06-22-2009 04:08 PM )

by on

0 Comments 4199 Views

0 Comments

4199 Views

Router loads Cisco IOS after a tftpdnld command upgrade, yet no file is in Flash due to the -r switc... - ( ‎06-22-2009 04:09 PM )

by on

0 Comments 4147 Views

0 Comments

4147 Views

A Cisco 2600 or 3600 series router boots to ROMmon mode when a modem is attached to the console port - ( ‎06-22-2009 04:39 PM )

by on

0 Comments 2879 Views

0 Comments

2879 Views

Cisco 2600, 3600, and 3700 series routers reload continuously - ( ‎06-22-2009 04:39 PM )

by on

0 Comments 1766 Views

0 Comments

1766 Views

The 7200 series router fails to boot from Flash disk - ( ‎06-17-2009 10:20 PM )

by on

0 Comments 2004 Views

0 Comments

2004 Views

Supervisor Engine module does not come online due to continuous booting loop, invalid boot variable,... - ( ‎06-22-2009 04:45 PM )

by on

0 Comments 2041 Views

0 Comments

2041 Views

Watchdog timeouts on 2600 and 3700 series routers with an AIM module. Router locks up upon bootup - ( ‎06-22-2009 05:05 PM )

by on

0 Comments 2375 Views

0 Comments

2375 Views

User receives the "Pinnacle Synch Failed" error message at bootup due to either a mis-seated module ... - ( ‎06-18-2009 03:56 PM )

by on

0 Comments 818 Views

0 Comments

818 Views

Top Tagged

A router produces error messages followed by the %SYS-6-BOOT_MESSAGES: Messages above this line are ... - ( ‎06-22-2009 06:14 PM )

by on

0 Comments 3779 Views

0 Comments

3779 Views

During MSFC bootup, the "%SYS-6-READ_BOOTFILE_FAIL" error message appears in Catalyst 6500 series sw... - ( ‎06-22-2009 06:13 PM )

by on

0 Comments 3190 Views

0 Comments

3190 Views

Supervisor Engine 720 crashes while it tries to bootup in a Cisco Catalyst 6500 Series switch runnin... - ( ‎06-22-2009 06:10 PM )

by on

0 Comments 1625 Views

0 Comments

1625 Views

The boot loader does not appear in the output of the "show version" command, although the output of ... - ( ‎06-22-2009 05:39 PM )

by on

0 Comments 1134 Views

0 Comments

1134 Views

Cisco Catalyst switch in ROMMON mode ("switch:" prompt) after a software upgrade - ( ‎06-22-2009 05:37 PM )

by on Latest post on by

2 Comments 77432 Views

2 Comments

77432 Views

A Novell IPX workstation does not have the Novell Login Screen at bootup due to spanning tree delays - ( ‎06-22-2009 05:35 PM )

by on

0 Comments 1081 Views

0 Comments

1081 Views

A new image takes time to load in Catalyst 6000/6500 Series Switches after a software upgrade - ( ‎06-22-2009 05:35 PM )

by on

0 Comments 791 Views

0 Comments

791 Views

How to convert the router from normal execution mode to ROMMON mode - ( ‎06-22-2009 05:34 PM )

by on

0 Comments 2919 Views

0 Comments

2919 Views

Card in a modular Catalyst 4000, 5000 or 6000 series chassis does not function properly or is not on... - ( ‎06-22-2009 05:33 PM )

by on

0 Comments 2781 Views

0 Comments

2781 Views

The router reports the device does not contain a valid magic number error message and fails to load ... - ( ‎06-22-2009 03:38 PM )

by on

0 Comments 7035 Views

0 Comments

7035 Views

Top Taggers

User

Count