Tag: "port_issues" - Cisco Community

Buy or Renew

Latest Tagged

Recovering from ErrDisabled port due to misconfiguration - ( ‎06-22-2009 04:39 PM )

by on Latest post on by

2 Replies 222128 Views

2 Replies

222128 Views

CiscoWorks reports a Port HighDiscardRate message for gigabit ports on the Cisco Catalyst switches - ( ‎06-22-2009 03:36 PM )

by on

0 Replies 880 Views

0 Replies

880 Views

Configuring EtherChannel results in ports being errdisabled, and fails to form channels due to spann... - ( ‎06-18-2009 03:53 PM )

by on

0 Replies 637 Views

0 Replies

637 Views

The Incorrect trunk type specified for port error message is displayed during the configuration of t... - ( ‎06-18-2009 04:00 PM )

by on

0 Replies 556 Views

0 Replies

556 Views

The output of the show interface status command does not display the type of GBIC in Cisco Catalyst ... - ( ‎06-22-2009 04:40 PM )

by on

0 Replies 14968 Views

0 Replies

14968 Views

When redundancy is run, unable to use all eight ports on both of the Supervisor 5 engines in a Catal... - ( ‎06-22-2009 05:33 PM )

by on

0 Replies 1046 Views

0 Replies

1046 Views

Cisco IOS® ソフトウェアを実行している Cisco Catalyst スイッチに「%ETHCNTR-3-LOOP_BACK_DETECTED」エラーメッセージが表示される - ( ‎05-23-2011 07:30 PM )

by on

0 Replies 7200 Views

0 Replies

7200 Views

VLAN interface status is up/down when there is no device connected to the port - ( ‎06-18-2009 03:53 PM )

by on Latest post on by

1 Replies 15621 Views

1 Replies

15621 Views

Unable to connect Catalyst switch to the Ether Switch Module on a router that uses the straight thro... - ( ‎06-22-2009 03:42 PM )

by on

0 Replies 565 Views

0 Replies

565 Views

Port status is errdisable due to EtherChannel misconfiguration - ( ‎06-22-2009 05:10 PM )

by on

0 Replies 20584 Views

0 Replies

20584 Views

Top Tagged

When port security is enabled, MAC addresses are detected but after a short while the port is shut d... - ( ‎06-22-2009 06:12 PM )

by on

0 Replies 1165 Views

0 Replies

1165 Views

The "%DOT1X_SWITCH-5-ERR_ADDING_ADDRESS:" error message appears in Cisco Catalyst 3550 or 3750 serie... - ( ‎06-22-2009 06:07 PM )

by on Latest post on by

2 Replies 7022 Views

2 Replies

7022 Views

How to run GOLD diagnostic tests on Catalyst 6500/6000 series switches to troubleshoot hardware issu... - ( ‎06-22-2009 05:38 PM )

by on

0 Replies 17415 Views

0 Replies

17415 Views

How to configure the errdisable flap-setting values in Cisco Catalyst switches running Cisco IOS sys... - ( ‎06-22-2009 05:37 PM )

by on Latest post on by

2 Replies 12462 Views

2 Replies

12462 Views

User cannot get a Gigabit Ethernet link up between a Cisco switch and a non-Cisco device due to auto... - ( ‎06-22-2009 03:40 PM )

by on

0 Replies 1184 Views

0 Replies

1184 Views

The %RTD-1-LINK_FLAP [chars] link down/up [dec] times per min error message appears on a port - ( ‎06-22-2009 03:40 PM )

by on

0 Replies 3723 Views

0 Replies

3723 Views

Runts and CRC errors increment in the show interface command output on a Cisco IOS-based switch, or ... - ( ‎06-22-2009 03:40 PM )

by on

0 Replies 69504 Views

0 Replies

69504 Views

A SPAN destination port is shown as "not connected" and does not communicate with the rest of the ne... - ( ‎06-22-2009 05:35 PM )

by on

0 Replies 6756 Views

0 Replies

6756 Views

The "%C4K_HWPORTMAN-4-BLOCKEDTXQUEUE" error message on Cisco Catalyst 4500 series switches connected... - ( ‎06-22-2009 05:34 PM )

by on Latest post on by

2 Replies 21666 Views

2 Replies

21666 Views

When redundancy is run, unable to use all eight ports on both of the Supervisor 5 engines in a Catal... - ( ‎06-22-2009 05:33 PM )

by on

0 Replies 1046 Views

0 Replies

1046 Views

Top Taggers

User

Count