ā08-26-2014 08:11 AM - last edited on ā03-25-2019 09:12 PM by ciscomoderator
Hi,
Looking at replacing some Polycom HDX systems. With the HDX you can do dual screen emulation on a single screen. Is this supported on the SX range?
Thanks
George
Solved! Go to Solution.
ā08-27-2014 04:43 AM
Hi
Have you tried TC-Console? There you can have one monitor and divide the screen how you like. Once you have divided the monitor into how many screens you want then you can assign each screen an input, i.e input 1 (camera) on screen 1, main participant on screen2, local presentation on screen 3, input2 on screen 4 (secondary camera) for example.
The possibilities are many. You can mix around with audio as well.
Please find the application here: http://software.cisco.com/download/release.html?mdfid=286271155&flowid=71282&softwareid=280886992&release=TC-console-v7.1.2&relind=AVAILABLE&rellifecycle=&reltype=latest
ā08-27-2014 05:15 AM
Selfview will show as a PIP, however if pc content is shown, you have a few different options regarding the layouts. Attached is a screenshot of the layouts available when you send content.
ā08-26-2014 10:14 AM
The SX20 and SX80 supports 2 and 3 screens respectively.
http://www.cisco.com/c/en/us/products/collateral/collaboration-endpoints/telepresence-sx20-quick-set/data_sheet_c78-688342.html
http://www.cisco.com/c/en/us/products/collateral/collaboration-endpoints/telepresence-quick-set-series/datasheet-c78-731242.html
ā08-27-2014 01:57 AM
Hi George,
It's emulating two screens on a single monitor.
Thanks
ā08-27-2014 04:43 AM
Hi
Have you tried TC-Console? There you can have one monitor and divide the screen how you like. Once you have divided the monitor into how many screens you want then you can assign each screen an input, i.e input 1 (camera) on screen 1, main participant on screen2, local presentation on screen 3, input2 on screen 4 (secondary camera) for example.
The possibilities are many. You can mix around with audio as well.
Please find the application here: http://software.cisco.com/download/release.html?mdfid=286271155&flowid=71282&softwareid=280886992&release=TC-console-v7.1.2&relind=AVAILABLE&rellifecycle=&reltype=latest
ā08-27-2014 05:04 AM
FYI
SX80 supports TC Console, but not SX20 because SX20 is a quick set system and SX80 is an integrator system.
/Magnus
ā08-27-2014 07:02 AM
Hi Magnus,
Thanks for the that. It would be a SX80 that I would be using for 50/50 side by side.
Cheers
ā08-26-2014 10:21 AM
Hello George -
You can have the far-end video and either: selfview, pc content, or both (selfview and pc content) all on the same single screen. Haven't found a document that shows the different layout options yet, if I do, I'll post it.
ā08-27-2014 02:01 AM
Hi Patrick,
I've been trying it on a SX20 and can only get it as PIP, also can't find any documentation. The Polycom's give you an option to do a 50/50 screen split. If you do find any documentation it would be appreciated.
Cheers
ā08-27-2014 05:15 AM
ā08-27-2014 07:05 AM
Hi Patrick,
Thanks for looking into this. It would be nice if Cisco would provide the equal view as a side by side instead of top and bottom as the screen I will be using is a 65" widescreen.
Cheers
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide