04-25-2014 03:51 AM
Hi all,
We are facing the process to update CUCM and I&M on a BE6K platform from 9.1 version to the latest one. I understand that this type of upgrade is standard.
If I am not getting wrong we would need a COP upgrading file for CUCM and another one for I&M. We´ve been browsing looking for these files but we didn't get them. Could someone put us on the right direction?
Thanks in advance.
Regards
04-25-2014 04:09 AM
You don't need any COP file for 9.x upgrade. Its needed only for 8.5.x & older as documented here Upgrade Guide for Cisco Unified Communications Manager, Release 10.0(1) - Upgrade planning [Cisco Unified Communications…
Cheers !!
GP.
04-25-2014 04:39 AM
So, what would we need then in order to perform the update? we've browsed looking for iso file as well with no results.
04-25-2014 04:44 AM
Following note is found on the CCO Download page
All upgrades to UCM 10.0(1) require new licensing which must be entitled by an
order placed through the Product Upgrade Tool or the usual ordering process.
Orders may be fulfilled electronically or physically, whichever is preferred.
GP.
04-30-2014 02:26 PM
As gapande said and as per Cisco CUCM 10.0.1 upgrade guide you don't need the cop file. I'm working at this moment on the same task. I will update you as soon as we get the result.
Regards]
05-28-2014 06:37 AM
Hi Garcia,
As Gajanan mentioned, upgrade from 9.1 to 10.x is a major release upgrade, so you need to order user migration licenses for this upgrade (unless you have UCSS, which covers you for major release upgrades and you can use Product upgrade tool to order media/licenses).
Then you just follow the process of a major release upgrade (order/download 10.x media, install upgrade on inactive partition, switch partitions, install licenses etc. )
For details, find the relevant CUCM install and upgrade guide and go through it.
I hope this helps!
Regards,
Zeeshan
01-23-2015 08:44 AM
Hi,
So, I will do the same upgrade (CUCM,CUC and IM&P 9.1 BE6K to version 10.1) and I would like more datail information about each steps to use Product Upgrade Tools. I would know if is necessary upgrade the ova template in vmware as well (memory vRAM, disk vDisk and vCPU)?
Best regards,
Daniel
01-26-2015 08:29 AM
Daniel,
I recommend you also post this to the Cisco Partner Community for additional information and feedback.
Kelli Glass
Moderator for Cisco Customer Communities
01-26-2015 09:02 AM
Hi Daniel,
You don't need to upgrade the OVA templates. Just order the media/licenses through Product Upgrade Tool (http://tools.cisco.com/gct/Upgrade/order.do) if you have a valid UCSS/SWSS cover, otherwise you have get in touch with your support partner and order the migration licenses to version 10.x.
Once you have got the media and licenses sorted, then you will have to install the upgrade/version 10.x software on inactive partitions on relevant application servers/VMs and reboot to switch over the partitions. Note that your phones will go into firmware update cycle when you cutover to new CUCM version. If you like you can do the phone firmware upgrade before the actual upgrade by loading the new device pack.
Hope this helps!
Regards,
Zeeshan
01-27-2015 03:04 PM
Hi Zeeshan,
I have confirmed that has UCSS valid. I will do the steps that you say.
Thank you very much.
Best regards,
Daniel
02-12-2015 11:33 AM
Hi Zeeshan,
In contact with Cisco TAC, the engineer told me that need install in CUCM 9.x a RU <ciscocm.refresh_upgrade_v1.5cop.sgn> to config the system from <Linux enterprise Red Hat 5 32-bit> to <Linux enterprise Red Hat 6 64-bit>. After that upgrade I would apply the patch upgrade 10.5 for the CUCM.
Best regards,
Daniel Sobrinho
02-16-2015 04:03 AM
Great Daniel!
I am pleased to find out that you are progressing with your upgrade.
Regards,
Zeeshan
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide