About chenbs

chenbs · 05-13-2022

I am deploying a new ACI fabric. We are using Nexus 9364C-GX as spine switches. I am unable to discover anything past the first leaf (which the apics are connected to) because the 9364C-GX can operate as both leaf and spine and by default it is opera...

chenbs · 03-25-2015

Dear all,I just wanted to know what your thoughts are on the following issue that I have. I have an internal Router that receives various subnets of the 10.0.0.0/8 from internal core routers via an IGP. I have an IPBGP peering with a WAN router which...

chenbs · 10-03-2008

I am using callmanger express 7.0 and am attempting to enable MOH.I have a combination of 7961, 7940, 7960 handsets. I have used the following configuration:1. telephony-service 2. moh music-on-hold.au 3. multicast moh 239.10.16.4 port 21234. exit 5....

chenbs · 06-26-2007

Hi,I have a Cisco PIX 515E router with an unrestricted license. My internal users can access the internet via the leased line router connected to the outside interface. The DMZ users currently get out to the internet the same way. However, I have bee...

chenbs · 06-22-2007

Hi,I'm trying to upgrade a 3750 stack with three switches. One of the members has afile called "lslss". Do you know what it is used for ?. If it remains, I will not haveenough space to load the advanced ip image.Directory of flash2:/ 2 -rwx ...

chenbs · 05-19-2022

Hi Sergiu,It worked as we discussed. I temporarily patched the leaf's that have the apics to the fabric ports (63-64) on the spine. The Nexus 9364C-GX were then discovered by the APICS. I then registered them as spines and they rebooted as spines. On...

chenbs · 05-14-2022

Hi Sergiu,Good question. I will go back to site this coming week so I will try it and let you know. I may just move the ports connected to theLeaf switches that have the APICS attached to see what happens. Once the switch changes to a spine, the othe...

chenbs · 05-13-2022

On the Nexus 9364C which is fixed as spine only, you can use any ports as you cannot change the mode. It would be a shame if I have to use the ports from highest to lowest just to get the Nexus 9364C-GX to work as a spine switch

chenbs · 05-13-2022

Hi Sergiu, Many thanks for your reply. I am using aci-n9000-dk9.15.1.3e.bin. My issue may be because I am using ports 1-16 from the Nexus 9364C-GX and not the required ports below. Spine discovery via leaf – Connect a discovered leaf to one of the d...

chenbs · 03-26-2015

Hi Jon, I am just happy that you have taken time out to assist. Thank you so much and I will check and let you know when I have figured out the cause. Take care

Member Since	‎10-07-2004 05:38 AM
Date Last Visited	‎05-25-2022 12:02 AM
Posts	26

User Statistics

User Activity

Cisco Nexus 9364C-GX ACI default leaf mode

Advertise a specific subnet to a BGP neighbour out of an aggregate

CUCME MoH support for mixed 7940-7960 & 7941-7961

DMZ access to second Internet Router

Cisco 3750 "lslss". file

Re: Cisco Nexus 9364C-GX ACI default leaf mode

Re: Cisco Nexus 9364C-GX ACI default leaf mode

Re: Cisco Nexus 9364C-GX ACI default leaf mode

Re: Cisco Nexus 9364C-GX ACI default leaf mode

Hi Jon, I am just happy that