About EdvinasKairys11982

EdvinasKairys11982 · 10-25-2022

Hello,I'm preparing for NCS 5501-SE device upgrade from 7.0.2 to 7.5.2.There're one field notice which impacts my device: https://www.cisco.com/c/en/us/support/docs/field-notices/721/fn72108.htmlhttps://www.cisco.com/c/en/us/support/docs/field-notice...

EdvinasKairys11982 · 06-23-2022

I want to upgrade to newest recommended Bengaluru-17.6.3a(MD) version from this one: 16.09.03.the hardware i'm using is: ISR4451-X/K9 I know that it should be quite easy, just in configure mode enter: boot system bootflash:xxx.bin and reload. The ma...

EdvinasKairys11982 · 06-21-2022

I'm trying to run simple monitoring with Telemetry, by looking at this video: https://www.youtube.com/watch?v=erTyK0WDsT0&t=2556sI've configured everything, but Cisco device doesn't send any packet to the receiver. The server side uses Influxdb + Tel...

EdvinasKairys11982 · 07-16-2021

Hello,We got couple of N9K's - N9K-C9372PX-E 7.0(3)I7(8) For some reason they doesn't age out old MAC entries. Where're no custom configurations, the age time is left a default: Switch# show mac address-table aging-time Aging Time ---------- 1800Dyn...

EdvinasKairys11982 · 11-12-2020

Hello,When I initial configured our NCS routers, i used the same admin username for XR Vm, and sysadmin vm. Now to have more order in the system i want to separate them. Leave `admin` for root-lr, and use new user `adminxr` for xr vm. 1) I will creat...

EdvinasKairys11982 · 07-18-2023

but i'm using the qsfp to 10g sfp adapter, so i have only 1x10g per qsfp (CVR), and seems only the breakout number zero works in my case. Is there anything bad in my configuration ? In the CVR product page i see the notion "The SFP+ transceiver will ...

EdvinasKairys11982 · 07-18-2023

update: seems like (config)#hw-module quad 0 location 0/RP0/CPU0 mode 10g ? this command is not supported on platform.But as you said @smilstea i did local test between devices: hw-module port-range 0 1 instance 0 location 0/RP0/CPU0 mode 4x10and th...

EdvinasKairys11982 · 07-17-2023

Hello, thank you. I didn't do anything for the port configuration because i expect the port automatically turn into Tengig one. For example here https://xrdocs.io/ncs5500/tutorials/ncs5500-things-to-know/ in xrdocs it was written so: If you insert a ...

EdvinasKairys11982 · 10-25-2022

thank you, now i'm lost The upgrade matrix shows - that it's supported, attaching screenshot:

EdvinasKairys11982 · 10-24-2022

Thank you, will keep in mind. Also - maybe you know if i can also - at the same upgrade iteration add one of the SMUs ? To the same .tarball or `to the `install add source harddisk` command)

Member Since	‎07-15-2020 05:56 AM
Date Last Visited	‎01-29-2024 11:41 AM
Posts	24
Total Helpful Votes Received	20

User Statistics

User Activity

NCS 5501-SE upgrade from 7.0.2 to 7.5.2

upgrading ISR IOS-XE router to latest recommended version

IOS-XE telemetry doesnt work

Nexus 9K doesn't age out dynamic mac entries

changing root-lr password on sysadmin-vm

Re: QSFP to SFP adapter for NCS 5700

Re: QSFP to SFP adapter for NCS 5700

Re: QSFP to SFP adapter for NCS 5700

Re: NCS 5501-SE upgrade from 7.0.2 to 7.5.2

Re: after NCS 5501-SE upgrade from 7.0.1 to 7.0.2 - UPGD FAIL status