Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About buchholr
buchholr
Beginner
Started in networking with USAF. 5 years experience in AF. Started with Cisco Gold partner in March 2007, did pre-sales design, then went to post-sales installation work.
Recent Badges
Stats
Member since
04-26-2005
52
Posts
49
Helpful
4
Solutions
Certifications
Created by
buchholr
in IP Telephony and Phones
in IP Telephony and Phones
10-08-2013
01:40 PM
10-08-2013
01:40 PM
This is the System Event Log on the CIMC. You can log into the CIMC via web browser (if it has been set up), and review and clear the log. Button on bottom right side of screen clears log. Sometimes you have to scroll down to see it. HTH, Rob
... View more
10-07-2011
06:55 PM
For a production network, NEVER! Anything not sold through a authorized reseller is grey market at best. Cisco's licensing for IOS is not transferable, so you would have to buy a license for the IOS through a reseller. Also, to get Smartnet, you might have to pay to have the gear inspected before they will cover it. At worst, you could end up with black market gear. Knockoff equipment from foreign countries. Cisco won't even acknowledge you with this gear. If you are looking to save a little money, talk to your Cisco reseller about Cisco Authorized Refurbished equipment. Hope this helps Rob
... View more
05-30-2010
05:44 AM
These devices are very limited when in Rommon mode. You are typing "rename config.text config.old" and "delete config.text." I have never know this syntax to work when in Rommon. Because the switch has no idea where to find the file, it gives you an unhelpful error message. Try using "rename flash:config.text flash:config.old" if you want to keep the old configs for some reason, or if you don't try "delete flash:config.text." Hope this helps, Rob
... View more
04-18-2010
05:13 PM
There is still a lot of information needed before anyone can answer your question. First, what supervisor are you running now? Sup 1a, Sup 2, Sup 32, or Sup 720? Are you running redundant supervisors? Are you replacing the current supervisor with the same type, or are you upgrading to a VSS or Sup 720? Are you running in hybrid mode (Cat-OS and IOS), or are you running in Native (IOS only)? If you are upgrading from a sup2 or older, you may have to reconfigure your blades to accomidate supervisor 720s (they have to go in slots 5 & 6). With this information, we can provide more help on your request. Rob
... View more
There are two generations of the 831. The earlier generations only had 32 MB onboard, and the later versions had 48 MB onboard. However, both only permitted a 16 MB card to be installed int the DRAM slot. Here is a link to the memory upgrade documentation for the 800 series routers: http://www.cisco.com/en/US/partner/docs/routers/access/800/hardware/notes/800upgrd.html#wp41897 It sound like your router is doing what it is supposed to do in terms of the memory in the DRAM slot. You may have had part of your onboard memory fail. HTH, Robert
... View more
Created by
buchholr
in IP Telephony and Phones
in IP Telephony and Phones
02-16-2010
02:32 PM
02-16-2010
02:32 PM
Not as simple a question as you would think. There is no set amount of time for a ring. However, I believe the issue you are running into is not in you mobileconnect settings, but rather in your line settings. The system defaults to 12 seconds for the call forward no answer timer. On our systems, we have had to adjust this timer for users with mobility turned on to 20 seconds. You can do this in the line settings at the bottom of the forwarding settings for individual lines, or you can set it globally for all phones in the services settings. Robert
... View more
02-16-2010
08:52 AM
1) No, until just recently 7.1 was the latest. 8.0 has now been announced. 2) No, It looks like 4.0 is the latest it can support on that platform. 3) You will need PVDM resources for any FXO, FXS, or T1 ports. The HDV card has the slots for these. Rob
... View more
Created by
buchholr
in IP Telephony and Phones
in IP Telephony and Phones
02-16-2010
08:22 AM
02-16-2010
08:22 AM
If you have SRST, then you can turn on CME. The IOS version and feature sets are the same for both. Just remove all of the SRST configs, and reconfigure as a CME. As for the Unity express, you will need to purchase a module. There are a couple of modules, and AIM and a NME. The NME can support a lot more boxes and ports, and it also boots much faster. If all you are using it for is a lab, then the AIM will suffice. If you are using it in production I would tend to recommend the NME. Rob
... View more
02-15-2010
04:35 PM
This error doesn't have anything to do with the IOS on flash. This is an indicator of a bad DRAM chip. Replacement of the bad chip is the only option. There are several companies that sell chips for older platforms. Robert
... View more
02-15-2010
04:08 PM
Can you post the output of a "show ip route" command from the router? I have seen on rare occasions I have seen routing turned off on a router. If that is the case, the output of the above command is different than normal. It can be turned back on with the "ip routing" command. It is a long shot, but I just don't see anything immediately wrong with your configs. Robert
... View more
02-14-2010
09:19 AM
Some of your phones will be OK. A lot will not. Here is a link to a document on Identity Based Network Services (IBNS). https://www.cisco.com/en/US/prod/collateral/iosswrel/ps6537/ps6586/ps6638/whitepaper_c27-574041.pdf Here is a quote from that document that rules out several of your phone models. "Cisco IP Phone models prior to Cisco’s third generation do not support X.509 certificates (for example, 7902, 7905, 7910, 7912, 7920, 7935, 7936, 7940 and 7960) and therefore have no road map to support IEEE 802.1X." I haven't found any direct reference to the ATA, but I doubt it will do .1x. They just aren't that advanced. Robert
... View more
Created by
buchholr
in IP Telephony and Phones
in IP Telephony and Phones
02-14-2010
07:21 AM
02-14-2010
07:21 AM
I don't know all of the information for your specific implementation. However, I have worked with these boards in the past. Please don't feel like I am being patronizing, but when I have issues like this I step back to the basics. First: Do you have a the correct cable for this connection. It should be a RJ48 crossover. This has the same ends as an RJ45, but is wired as below: Pin 1 -> Pin 4 Pin 2 -> Pin 5 Pin 4 -> Pin 1 Pin 5 -> Pin 2 Second: make sure the coding and framing match. Typically on a short span, you connect with B8ZS, ESF. Also make sure the router is providing timing for the link. Third: I don't know if you are planning to use T1CAS or PRI, but if it is PRI you need to make sure the ISDN switch type matches between the two systems, and make sure that one us set for network side (probably the router) and the other is user side. At this point, if everything matches, you should have a carrier between the two systems, and they should be able to talk. A running config would help me see what you are trying to accomplish. Robert
... View more
02-14-2010
06:22 AM
Without having a running configuration to look at, it sounds like you have multicast music on hold configured without having IGMP running. It is harmless in most small networks, but I never like having that much activity showing. To turn on PIM and, as a result, IGMP and allow the switch and router to "prune" back interfaces that don't need the MoH stream, try the following commands: ip pim rp-address x.x.x.x (this address is usually preferred to be a loopback on the router) ! interface TYPE X/X (the interface for the voice vlan, also run this on the interface you used above as your RP) ip pim sparse-mode ! This is a very basic config, and I am guessing about the music on hold, as I don't know how you are actually configured. If you want to post a running-config, I can confirm this, and give you a more specific config. Robert
... View more
01-17-2010
05:48 PM
I have not touched one of these myself, but the module should show up in a show inventory. If it does not, you could try a show diagnostic. You are running a new enough IOS that it should recognize the module and the inline power commands, so I would guess that you most likely don't have the module installed. Depending on who you purchased the system from, it could come installed or in a separate package. The way Cisco packages items, it would be hard to miss the extra part. It would be a fairly large box. Hope this helps, Robert
... View more
Created by
buchholr
in IP Telephony and Phones
10-08-2013
10-08-2013
This is the System Event Log on the CIMC. You can log into the CIMC via
web browser (if it has been ...
10-07-2011
For a production network, NEVER!Anything not sold through a authorized
reseller is grey market at be...
Created by
buchholr
in Unified Communications Infrastructure
04-25-2010
04-25-2010
According to the supported platforms list, this server is supported.
However, you have to upgrade it...
04-18-2010
There is still a lot of information needed before anyone can answer your
question. First, what super...
Created by
buchholr
in IP Telephony and Phones
02-16-2010
02-16-2010
Not as simple a question as you would think. There is no set amount of
time for a ring. However, I b...
02-16-2010
1) No, until just recently 7.1 was the latest. 8.0 has now been
announced.2) No, It looks like 4.0 i...
Created by
buchholr
in IP Telephony and Phones
02-16-2010
02-16-2010
If you have SRST, then you can turn on CME. The IOS version and feature
sets are the same for both. ...
02-15-2010
This error doesn't have anything to do with the IOS on flash. This is an
indicator of a bad DRAM chi...
02-14-2010
Some of your phones will be OK. A lot will not. Here is a link to a
document on Identity Based Netwo...
02-14-2010
I don't know all of the information for your specific implementation.
However, I have worked with th...
Public Statistics
| Date Registered | 04-26-2005 10:27 AM |
| Date Last Visited | 11-05-2019 11:15 PM |
| Total Messages Posted | 52 |
| Total Helpful Votes Received | 49 |
