About Philidor

Philidor · 09-21-2022

We've a cisco 2811 with IOS c2800nm-ipbase-mz.124-13d.bin and the following module is installed but we can't configure ATM.Is it caused by the wrong module or wrong IOS ?NAME: "Two port E1 voice interface daughtercard", DESCR: "Two port E1 voice inte...

Philidor · 09-19-2022

Backup router log is showing isdn activities occurred on today and yesterday, while last time main link flapped occurred on Sep 17thSep 18 03:19:40.219 CET: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 68 changed to upSep 18 03:19:54.934 CET: %IS...

Philidor · 09-14-2022

Sh ver is showing that yesterday at about noon router was switched off and on and after the reset wan connection restarted to work uptime is 20 hours, 52 minutesSystem returned to ROM by power-onSystem restarted at 11:58:26 NFT Wed Sep 14 2022System...

Philidor · 01-26-2022

A Cisco 2811 Fa0/0 is connected to a Cisco WS-C4507R Gig 3/11 through one Km of mono-modal optical fiber and 2 copper-fiber converter (one near the router and the other one near the switch). We very very often get the following alarms. We've already ...

Philidor · 11-19-2021

This router, with IOS c1841-spservicesk9-mz.151-3.T4.bin, is used for umts backup, which is not working, with cellular profile always inactive. SIM is active and not disabled, without any traffic limitation, but it hasn't been connecting successfully...

Philidor · 09-21-2022

I previously attached a couple of files with pieces of config of the main and backup router. By the way, both the routers are connected to a common switch.aitan8o6ap#sh standEthernet0 - Group 1Local state is Standby, priority 100, may preemptHellotim...

Philidor · 09-21-2022

Thank you.I'll try with the right IOS and I will let you know.

Philidor · 09-21-2022

Exactly I have the following doubt because with the following module installed always on a cisco 2811 we can configure ATM.NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Mu...

Philidor · 01-31-2022

I can't be fully sure but I believe an OTDR has been run. Fiber attenuation is fine and equal to 3,697 dB/km (Fiber 1) and 4,263 dB/km (Fiber 2)

Philidor · 01-27-2022

The fiber path has been successfully tested after that we detected the problem to ensure its integrity. Please note after this show I've cleared the interface counters sh int fa0/0FastEthernet0/0 is up, line protocol is upHardware is MV96340 Ethernet...

Member Since	‎11-19-2021 09:36 AM
Date Last Visited	‎09-28-2022 12:01 AM
Posts	12

User Statistics

User Activity

With VWIC-2MFT-E1 module unable to configure atm

Isdn backup invoked without an apparent reason

Cisco 1721 doesn't show a reload in the log

Bad LAN connection between a cisco 2811 and a switch

Cisco 1841 cellular 0/0/0 profile always inactive and backup down

Re: Isdn backup invoked without an apparent reason

Re: With VWIC-2MFT-E1 module unable to configure atm

Re: With VWIC-2MFT-E1 module unable to configure atm

Re: Bad LAN connection between a cisco 2811 and a switch

Re: Bad LAN connection between a cisco 2811 and a switch