Hi Namit and Rahul, now I need your special Cisco competences. In short: during a passthrough IPsec  connection from a foreign router (RouterX) behind the Cisco RV180 the  tunnel brakes off after short time. 1. RouterX --> RV180 --> Internet provider --> Destination Router = does not work after short time 2. RV180 --> another RV180 (site2site) = works fine. The VPN established from the foreign router through Cisco RV180. At  first 10 minutes the IPsec connection works fine. But after this time  the IPsec packets are lost. All VPN passthrough option are activated in the Cisco RV180 configuration menu. When the Cisco RV180 restarted the connection will be reconnect successfully. And the problem repeats again... But the own Site-to-Site IPsec connection from RV180 to RV180 always works fine. The foreign router establishes the IPsec connection to destination router without problems. This contruct works fine everytime. This problem refers to IPsec traffic through Cisco RV180 only. Do you know the problem about this "lost packets"? Why VPN passthrough doesnt work correctly in this small business appliance? Thanks Alex ... View more

Hello, in ACS there is a configuration with radius request "simulataneous login=1". If I hold a vpn session for a time x another user (X) can login with the same user data during the connection. After user (X) is connected and my active session was canceled (by another user). The active session changed to user (X). In ACS I give authentication request "Radius Cisco VPN3000/ASA/PIX7.xSimultaneous-Logins=1". Is there a way to deny the connection for user (X) during an existing vpn session? What is the option or request in ACS? Thx for help! ... View more

Hallo, I have a question about the policy mapping in ACS 5.4. When a request matches in "Access Selection Rule" the request goes to an "Access Service". In "Access Service" there are three kinds of policy rules: - Identity: If condition match then result "Identity Source" - Group Mapping If condition match then result "Identity Group" - Authorization If condition match the result "Auth Profil" Q1: For example: The User "Test" is registered in Internal User with a local password. But now I will authenticate the user "Test" from a RSA Token server. How can I configure this rule in "identity policy"? Wich condition matches to choose the identity source. I will set the internal user with an attribute enumeration field like "Password". The administrator should have an option to choose "locale databse password" or "token passcode". Q2: What does it mean: "Group mapping"? Thx for your answer! Stefan ... View more

Hi all, I have a question about the performance of the UCCX 7.0(1) SR05_Buil504. (Package: Cisco Unified CCX Premium) How many calls can this version handle? (calls per hour or day) How many agents can work with the agent desktop? (at the same time) Are there other parameters that I must know? I know that the UCCX 7 has a maximum of 150 CSQs.  Is that right? Thanks for your answer... Best Regards. ... View more

'Hello, I've a problem with RPS on Cisco Cat2960. Since the switch has power loss, the yellow LED blinks on RPS status. Because the switch is obstructed in another building I will reset the RPS status via IOS. Is it possible? The power supply is connected through the switch and RPS. Kind regards ... View more

Hallo, I  have a great problem with our time synchronization. In our network  there are two switches Cisco 3750E (as coreswitch). One of them (first)  has a default ntp (server external) but the other switch cannot sync the  time from the first switch. The time from the second switch is after 15  minutes. How can I sync this second switch with the first one? Which command can I use to sync a switch with another source? #conf t config#ntp server 192.168... .. It does not work. The server is registered but not sync... fyi: #show ntp associations          adress             ref clock   st   when   poll      reach +~192.53.103.108      .PTB.       1    477    1024    377 * ~192.53.103.104      .PTB.       1    160    1024    377 Thanks for your help! Best regards, Alex ... View more

Hallo, I have a great problem with our time synchronization. In our network there are two switches Cisco 3750E (as coreswitch). One of them (first) has a default ntp (server external) but the other switch cannot sync the time from the first switch. The time from the second switch is after 15 minutes. How can I sync this second switch with the first one? Which command can I use to sync a switch with another source? #conf t config#ntp server 192.168... .. It does not work. The server is registered but not sync... fyi: #show ntp associations          adress             ref clock   st   when   poll      reach +~192.53.103.108      .PTB.       1    477    1024    377 * ~192.53.103.104      .PTB.       1    160    1024    377 Thanks for your help! Best regards Alex ... View more

Hello, I'm working on Cisco-Network(with Coreswitch Cisco 3750E). Since two weeks the core switch has an utilization of 100% (every ten minutes). The nagios reports the following message: "cisco_load | CPU: 99 99 99 : 99 > 98". In IOS command: 3750E#show proc cpu result: 316     8864348    869362      10196 74.49% 77.95% 78.33%   0 SNMP ENGINE Why the snmp has a load over 70%? Can you help me? I take this information in a forum: There are two probable causes for high CPU  utilization occuring in relation to Simple Network Management Protocol  (SNMP): Large route and/or ARP tables being polled by the NMS station Polling certain MIBs How can I get the #show proc cpu histroy# in real time? Best regards ... View more

Hello, I want to get the (#show vlan)- table from a cisco switch (IOS) to a file f.g. Visio or Excel. Is there a way to write this command in a file? Thank for your help! Best regards... ... View more