About Shiden

Shiden · 02-26-2024

Hi all,This is my first time working with EWC, and I'm a bit confused about the joining process of the access point.First, here are the hardware components I'm working with:Access Point: C9120AXE-EEWC: C9130AXE-EWC-EVersion: 17.9.4aI don't understand...

Shiden · 04-04-2023

Hello all,I recently configured a physical WLC C9800-L-F. Here are some details about the WLC that could be useful:Model: C9800-L-F-K9Firmware: Bengaluru-17.6.4I configured two Switched VLAN Interface. One of them is used as management interface in V...

Shiden · 04-04-2023

Hello all,I recently configured two physical WLC C9800-L-F. Both WLCs are redundant and configured with HA SSO Switchover. The HA SSO is working perfectly so far.Here are some details about the WLC that could help:Model: C9800-L-F-K9Firmware: Bengalu...

Shiden · 02-22-2023

Hello all,I am currently configuring HA SSO with RMI+RP on a Catalyst 9800-L (Firmware 17.06.04) Wireless controller.The peering works perfectly:WLC#sh chassis RmiChassis/Stack Mac Address : 0845.d117.c840 - Local Mac AddressMac persistency wait tim...

Shiden · 02-27-2024

Hi @Rich R ,As described in my first post, the C9130AXE-EWC-E has been bought as wireless controllers with the factory installed EWC software and the C9120AXE-E as access point with only the CAPWAP image installed (not C9120AXE-EWC).Best regards

Shiden · 02-27-2024

Hi @Rich R ,Yes, I am. This is why I was surprised and why I wrote this post. I don't understand why the EWC behaves like that. For me, it makes no sense to transmit by default an EWC image to access points that initially only have an CAPWAP image an...

Shiden · 02-27-2024

Hi @Rich R ,I just saw that the secondary EWC switched from the EWC to the CAPWAP image over night even he should stay EWC. So it's important to set the IP address of the EWC and the access point to a static IP address.I really do not get why Cisco d...

Shiden · 02-27-2024

Hi @Rich R ,Thanks you for your answers. But here we are at my initial question again. Before they join the EWC, the access points (C9120AXE) have the pure CAPWAP image installed , I verified it. It's only when they join the EWC (C9130AXE-EWC) they a...

Shiden · 02-26-2024

Hi @Rich R ,The DHCP option 43 is a good point, thanks! It just tried it and it work well. I will probably use this solution.Well your choice is run them as pure CAPWAP software or EWC capable in CAPWAP mode.But as we discussed before it would not be...

Member Since	‎02-22-2023 12:55 PM
Date Last Visited	‎09-05-2024 07:54 AM
Posts	18
Total Helpful Votes Received	5

User Statistics

User Activity

Why, when AP joins EWC, the AP gets an EWC image

Wireless Management Interface IP change after rebooting or switchover

WLC C9800-L-F memory of bootflash runs full with RP system reports

HA SSO Switchover isn't triggerd when activ WLC loses default-gw

Re: Why, when AP joins EWC, the AP gets an EWC image

Re: Why, when AP joins EWC, the AP gets an EWC image

Re: Why, when AP joins EWC, the AP gets an EWC image

Re: Why, when AP joins EWC, the AP gets an EWC image

Re: Why, when AP joins EWC, the AP gets an EWC image